pla filament holder 3d models
583298 3d models found related to pla filament holder.thingiverse
A vise-mounted filament spool holder for use with Makerbot PLA filament.
grabcad
Guided by generative design. FEA simulation to prove well over 3X safety factor. Can hold two, 1kg spools on a 0.5" dowel. Some areas may be tricky to print. ... Uses two deck screws to fasten to a wall or stud.
thingiverse
Pincefil pour filament Ø1.75. ...Vous permet de ranger votre bobine proprement quand vous ne vous en servez pas. Filament holder for Ø1.75 wire. ...you can store your spools easyly when you dont use them
grabcad
It's a updated part for ....Rotary PLA Spool Holder for ALUNAR M508
thingiverse
56mm Spool Holder by joshvillbrandt is nice, but too tight to fit for my IAP's PLA material. Though based on joshvillbrandt's, I built from scratch. Instructions Print 2 pieces for both sides. ...Snap...
youmagine
It's a updated part of Rotary Spool Holder...https://www.youmagine.com/designs/rotatable-spool-holder
thingiverse
It's a updated part of Rotary Spool Holder(https://www.thingiverse.com/thing:3268649). ...
thingiverse
Customized version of https://www.thingiverse.com/thing:496521 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=496521
thingiverse
Customized version of https://www.thingiverse.com/thing:496521 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=496521
thingiverse
Customized version of https://www.thingiverse.com/thing:496521 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=496521
myminifactory
Just a simple filament holder for PLA Lite spool made by Filoprint (filoprint.it)
thingiverse
Easy holder for Filoprint PLA LITE spool.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=176442 Instructions Using the following options: spool_wall = 5 ring_cutouts = 0 bearing_diameter = 22 bearing_thickness = 8 cross_brace_include = include display_spool = hide bolt_diameter = 8...
thingiverse
I customized this original design http://www.thingiverse.com/thing:735213 with the following 3 important variable Tube Diameter - 30.5mm Height - 68mm Spool Diameter - 55mm this fits inside the Raise3D PLA and Raise3D Preimum PLA spools nicely, and...
thingiverse
Customized version of http://www.thingiverse.com/thing:72069 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=72069 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:72069 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=72069 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:72069 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=72069 Instructions Using the following options: w = 6.2 P...
thingiverse
Geeetech Prusa I3 Pro W filament roll holder on top (ABS/PLA) Printed in ABS with 50% of density. ... Donate what you want in https://www.paypal.me/Nadamas
pinshape
Geeetech Prusa I3 Pro W filament roll holder on top (ABS/PLA) Printed in ABS with 50% of density. ... Donate what you want in https://www.paypal.me/Nadamas
thingiverse
Printer brand: Creality Printer: Ender 3 Supports: Yes Infill: 40% Notes: Print these standing upwards/vertical. ...I printed the FilHolder_80mm vertical with the threaded end on the build surface.
thingiverse
Print your own swatches for all of your colours for PLA.
myminifactory
Print your own swatches for all of your colours for PLA. ... Layer 0,16 Infill 100
grabcad
filament spool by the OWL-filament brand. ...On this particular was PLA.
thingiverse
By sliding the filament through a sponge dabbed with oil, the PLA filament doesn't stick to the extruder heater tube. Instructions 1: Cut a small strip from a dense sponge and put it in the larger...