playseat challenge 3d models

Clamp to hold the Playseat Challenge chair closed.

Some simple clamps to keep the playseat challenge folded up. ...I wasn't a fan of using the straps, these just clip on and seem to work well.

Use this universal mount to proper secure things to a playseat challenge, or other things with 25mm tube diameter.I used it to mount the power-supply. ... Hardware needed: 2x M4x30 Screw 2x Washer for M4 2x M4 nut

A set of mounts designed to rigidly mount the Fanatec Clubsport V3 pedals to the Playseat Challenge. May also fit other pedal sets. ... More Information:...

It should be a quite good idea to add a adapter on Playseat Challenge on a side area. Tested on my E-brake working perfect. I printed by PETG infill 15% and 20% can get enough strength non breakable. Please enable support if need. ... Enjoy

I like it more, if my feet is more higher as the original default playseat challenge configuration. So I print me a T connector and a foot for a rod (21mm). ... It has 4 holes for screws and nuts (4mm) The Foot is only, to not damage my room floor,...

This clamp reinforces the entire pedal plate and makes it possible to use load cell pedals on the playseat challenge. I printed this in PLA 0.2 layer height. It's best to use supports inside the nut inserts for the bottom pieces. ... necessities...

Wanted to raise pedals height to get more "racing" feeling when driving with my Playseat Challenge chair, so designed this part to attach it under the Ø21 tube. I printed 2 of them and fixed both with metal plates I had at home to get better...

This is my favorite modification for my Playseat challenge. This cupholder will fit a water bottle (or beer) while doing some Sim Racing. No more awkward reaching to stay hydrated while in the pits! Take a sip of your favorite ale on the front...

I wanted to experiment with angling the pedals of my playseat challenge like some higher end rigs do. V1 attaches at the far end of the pedals, and would probably work well on hard floors. In my case, the carpet pad made the pedals rock side to...

The 3D printed parts necessary for enforcing the playseat challenge for fitting a CSL DD. Assembly: https://imgur.com/a/fHWt52l I've used a 40x3mm aluminum bar. Around ~1,2m or so of it to connect everything in between. The part i called...

Feet for the Playseat Challenge. Designed to fit some 50mm x 50mm glider or rubber pads. The glider allow me to easily move my seat around. The front feet can be fixed using zip-ties.</p><p><strong>Important:</strong> I designed the feet of the seat...

This is a can holder for the Playseat Challenge or other brands of racing chair. For anyone wondering why I made this and don't just simply put my drinks on the floor, well, I have a doggo, and he likes to touch things that are on the floor. This...

So, I went through the 10 realistic wheel plate positions for the playseat challenge, and did my best to measure what length and angle each one would need to work. I incorporated that into a dynamic FreeCAD model, where you just have to enter which...

I am actively redesigning this box as I've realized how little room it currently has for the hardware.** **Additionally, the clamp mount is not the best as it does come a bit loose over time and is not held at the best angle, nor is it at all...

Hi, this is a Bass Shaker Mount for the Playseat Challenge Seat. ... Thanks for donating paypal.me/Charliethingy

Playseat Challenge Red Locking Part. ...A bit tight to insert, but holds strong and don't need glue.

Playseat Challenge Red Locking Part. ...A bit tight to insert, but holds strong and don't need glue.

Remix of the original Playseat Challenge pedals raiser Printed in one piece, no iron brackets needed. ... Can be printed without support.

I wanted a robust shifter mount for the Playseat Challenge, and used the https://www.thingiverse.com/thing:2914511 as basis, creating a non adjustable and sturdy mount. Use three 6mm bolts to mount it to the Playseat. ...

I wanted a robust shifter mount for the Playseat Challenge, and used the https://www.thingiverse.com/thing:2914511 as basis, creating a non adjustable and sturdy mount. ...Use three 6mm bolts to mount it to the Playseat.

Provides better grip for moutings on a playseat Challenge or other 25mm sized tubes or rods Print this in soft filament (ninjaflex, soft PLA, TPU...) Printable in vase mode for 0.4mm nozzles

This is a remix of https://www.thingiverse.com/thing:4303004 by Shaykz. ... A holder for the Buttkicker Gamer 2 remote with a pipe clamp for the Playseat Challenge. ... I used some double-sided tape within the clamp.

This shifter bracket is specifically designed to fit the Logitech G29/G923/G920 and Thrustmaster TH8 on the Playseat Challenge racing seat. ... The bracket it's removable by losening the knobs, in order to store the seat without the shifter.

Here's a mount I designed that allows you to install a 25mm bar onto the leg frames (front or back) of a Playseat Challenge. I used this to attach my own Bass Shaker to my Playseat Challenge. ... Here's a 3 part video on how I did that showing the...

These pieces have the function of holding the pedals of the steering wheel to the support of the Playseat Challenge, without having to use the original velcro tape. ... To finish the installation of the piece, you need: -Screw zinc plated steel 6x40mm...

Also check out my other sim racing...

Mount for mounting body shakers (Bass Pump III) to the Playseat Challenge&nbsp;You need more simracing parts? Hace a look: <a...

I design and print this model to fix my handbrake to my playseat challenge. It can work for a shifter or anything else. You can rotate one piece to the other according to your position in the seat. ... Handbrake :...

Check out my shifter mount as well: https://cults3d.com/en/3d-model/gadget/playseat-challenge-thrustmaster-th8-shifter-mount It will also fit other frames with 1" (25,4 mm) tubing. Uses two M4x20 mm screws. ...Here's an assortment for various...