plug follower 3d models
507937 3d models found related to plug follower.
thingiverse
This is a plug follower used for Lock re-pinning. These typically run at least $2.50 per size and come in bags of $20-$40. I decided to make my own. This is the first version which is based on the ones you can buy. I have some ideas in mind for...
thingiverse
... ...All commercial plug follower designs I've seen have been hollow in the middle, this makes it a lot harder to use them for placing springs and top pins. ...Diameter is 12.6mm which will fit with most Australian locks.
thingiverse
... plug follower is a locksmithing tool used in the rekeying of pin-tumbler locks. ... This plug follower is 10mm in diameter and has an end that will fit the American Lock 1100 series key cylinder. ... It will also probably fit other similar style locks.
thingiverse
This LED Plug Follower will help you re-pinning your euro cylinder lock. You will also need : - 1x 5mm LED (3V) with long pins (anode must be approximately 30mm) - 2x AG3 or AG5 batteries - 2x cylinder springs (only one for AG5 batteries) - 1x...
thingiverse
This is a lighted plug follower, which allows you to see what you do when you repin a standard lock with a 1/2 inch (12.7mm) core. It also has the V-grooved front for aligning the pins nicely. Additional parts needed: -white (suggested) or any...
thingiverse
This is a set of plug followers based on the [Pro-Lok follower set](https://www.amazon.com/Pro-Lok-4-Piece-Follower-Set/dp/B073H56MZL) The Pro-Lock follower diameters are: follower 1 = 0.395" (10.03mm) follower 2 = 0.495" (12.57mm) follower 3 =...
thingiverse
A collection of plug followers. ... Euro plug follower. Euro sectioned plug follower. ... American Lock plug follower.
thingiverse
I purchased a set of pins with tools to re-key my locks at my house, but the generic plug follower that came with the kit didn't fit the back end of the plugs on the lever handles. Rather than waiting a few days for a commercial tool to come in, I...
thingiverse
This is a slim (9.6mm diameter) follower suitable for the core for an ABUS 72/40 padlock. ...It has a notch at one end, flat at the other.
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=847230 Instructions Using the following options: plug_follower_height = 10 plug_follower_type = 1 generate_base = 0 plug_follower_diameter = 10 notch_depth = 5 notch_width = 2 base_height = 2
thingiverse
This is a Kwikset Plug Following Tool with a 12.3mm diameter, used to insert into Kwikset entry lock barrels when removing the core while keeping barrel pins and springs in place. I printed on and Ender 3 at 100% infill and 0.2mm resolution. It...
thingiverse
... wall at the end. At the top I added a notch for the other side of the core. While this one is not required for extraction (it's the side of the key, so no pins to be expected), it helps to attach the follower to the core. ...Makes it more stable-
thingiverse
Master_padlock.stl -> tested on Master pro-series 6835 core with the flat edge Abus_padlock.stl -> tested on Brady LOTO/ABUS 71/40 core revolver_follower.stl -> To repin Sparows Revolver, [see video](https://youtu.be/3tVHvWSUrNI) US_0.5in_full.stl /...
thingiverse
Modified one with a bit of a foot for print adhesion and rotated it as well. ... Added a larger foot to prevent it being knocked off the build plate but it could also be a useful grip?
thingiverse
This is a 12.5mm diameter front / top loader for more easily repinning lock cylinders. ...Should handle 3.2mm pins
thingiverse
A collection of 5 different followers with 3 different diameters for the most common manufacturers. ... With these, you should be able to disassemble most locks without spilling out all the driver pins.