pop up camper support pole 3d models
866238 3d models found related to pop up camper support pole.thingiverse
This part attaches to the ceiling end of the shepherds hook, or tent support pole. You can find metal ones online, but this is a quick way to get up and operational again when your duck bill breaks off. All it takes is forgetting to remove it and -...
grabcad
Item is used on my 2010 Palamino 6149 pop up camper to secure the ridge poles to the interior frame of the slide outs.
thingiverse
On my 2006 Fleetwood Niagara pop up camper I have a slide out for the couch/table. To hold the canopy out there is a rod that pushes the frame of the slide canvas out then connects to the ceiling bracket to keep the rod up. This is for the side of...
thingiverse
... Measured and cut my ripped awning pole below the radius increase and then drilled out 3 1/8" holes with the part inside the pole, then rivetted in place. ... The rivets seem to hold really well and haven't had any issues with the part so far!
myminifactory
The Knightrunner Pop Up Camper was designed to fit into the bed of the Element Knightrunner. It will need to be glued to the bed with Shoe Goo or E6000 and we recommend using rear magnet mounts to make removal of the body easier. This set also comes...
thingiverse
This is a design I made for the cap that seals the odour inside my camper toilet. Mine Was broken so I designed this simple one... ... Work flawlessly!
thingiverse
curtain clip for Fleetwood pop up camper track. ...sews on like a button.
grabcad
This part works for older pop up campers with a swing-up door. This is part replaces broken twist door latches that hold up the door up against the ceiling. This confirmed to work with a vintage Viking pop up camper. ...Save yourself $10 a piece from...
thingiverse
Tent pole "knee" replacement for a pop up style tent along with a brace. Replacing the knee takes tools so also made a field brace should another break while we are out. The pole diameter is 8.5mm for both files. The brace holds the 20mm joint in...
thingiverse
This is the twist latch for locking your Pop Up camper door in place when you set up. It has a 1/4" off set and 3/16" screw hole. I ended up drilling it out to 7/32" because I had to go up to #12 screws because the holes on the camper were stripped.
thingiverse
The alignment posts for the two halves of the pop up screen door. One of mine broke, so I used the other to make a template. I reversed the file and this is the result. I have not tested it in my camper yet, but the dimensions are nearly identical to...
thingiverse
This is door turn button (the piece that you turn down to keep the top door linked to the bottom door once the camper is up). ... It is my first design and probably a little rough but it works.
thingiverse
On my camper the latch worked fine but the handle was broken, so I decided it would be good modeling practice for me to create a new one. For the entire latch assembly, the part number is 4742-9671,...
thingiverse
This is a camper top that works on a number of Matchbox models, such as the Impala Wagon and the Off-Road Trailer. It plugs right into the holes in the roof of these vehicles as if it came right from the factory. Has a tight fit so it does not fall...
thingiverse
Best results if you solid infill, but 10% infill is ok for single 3'x5' flag on a calm day, expect any more and ramp up infill accordingly. Depending on if you have a moving bed and how jerky it is, you may not need supports. ...My Ender 3 printed...
thingiverse
Clip for top header curtains in Fleetwood pop up camper. ...Sews on like buttons and slides well on existing track.
thingiverse
Provides tent and awning pole support. ...These pins are commonly found on the center canvas support poles and awning poles I used a 50% infill on PLA to provide for extra strength.
thingiverse
This is a support bracket for the elbow on the Quaddiction Pop-Up FPV Gates which aids in preventing the elbow from twisting in the wind and allowing the bridge to flop over. The collar will snap on to the existing elbow, and then slide up to press...
thingiverse
I designed this bracket for the awning of my Mars Camper trailer, but it will likely work on other brands with poles of the same diameter. The T shaped attachment goes on the tallest centre pole. Print as many washers as needed to centre the...
thingiverse
Print two copies and glue/weld together. Might need a little sanding or filling to get it to fit. You want it a little lose so that it can rotate but not come out. ... To remove this or original part, just heat with hot air to soften plastic and...
thingiverse
We 1997 Coleman Santa Fe Popup. ... It had a broken metal plate that hold the side bed popup top tent pole. We 3D printed a plate. Had to make it thick because version 1 bowed at bit. ...
thingiverse
I made this quick mount for a paper towel holder clips on to the heco lift system
thingiverse
This is a replacement post located on the bottom of the bed panels (when setup), which the bungee cord on the tent attaches. 1-1/4 screw required to mount. ...
thingiverse
this is designed to be used with hooked car tablet support, and installed in a camper.
thingiverse
Little supports for the turnbuckles commonly found in Jayco style camper trailers. ... Helps stop the turnbuckles being pulled laterally.