popsocket phone mount 3d models

This is a versatile phone mount for any device with a ball joint, and most mounts can accommodate balls. I picked up a basic bike mount for a Go-Pro camera at the store and realized that by removing the screw platform, I could use the socket mount...

Customized Version of Thingiverse Model 912161 Created with Customizer Tool at Thingiverse Website Instructions Using the Following Options: Phone Width Set to 66 Units Handlebar Diameter Measured at 35 Units Bridge Height Set to 30 Units Phone...

https://www.thingiverse.com/apps/customizer/run?thing_id=912161 Instructions Using the following settings: Bridge Height = Twenty Phone Width = Seventy-six Phone Corner Radius = Ten Handlebar Diameter = Twenty-six Phone Length = One hundred...

... Instructions Using the following settings: Phone width: 66 units Handlebar diameter: 35 units Bridge height: 25 units Phone corner radius: 10 units Phone length: 130.5 units Phone height: 11.5 units

Support Phones up to 8cm width and 1cm depth. ...Printed with no Support.

I really liked this phone tripod compatible mount by Redd (thing:3002681). But I wanted it to be a bit bigger so I could mount an iPad for my kids to do piano lessons via Zoom without any issues. I decided to make it chunky because I didn't want to...

This is an iphone 6s phone mount I designed as a proof of concept. The design prints in three parts. This is designed for a set of carbon fiber handlebars of 30mm dia. where if tightened too far, the print will fail before damage is done. To...

I created a small shelf that can hold most modern-sized cell phones, and it even accommodates my iPhone 6 in its Lifeproof Fre Power case with some extra room to spare. The screw holes are countersunk and sized to perfectly fit standard drywall...

This is a simple remix to mount the phone on the UK drivers side. The online customiser didn't work so I downloaded the .scad file and did the changes with openSCAD - essentially only changed the clamp_rotation to a negative value Settings used: ...

I was looking to model a similar phone holder to my RAM mount that I have on my motorcycle. I initially downloaded from Lay3rWorks (https://www.thingiverse.com/thing:1286674), but was worried my phone would not be secure enough when dirtbiking. I...

Steam Controller Phone Mount, with adjustable clip. If you print one of these, post it! ...I'd like to see!</p> <p><strong>READ ME BEFORE PRINTING!!</strong></p> <p>Need to print with supports,<strong>BUT</strong> you need to use Cura's "Support...

CAUTION: USE AT YOUR OWN RISK!Mount your phone in the middle of the handlebar with this 3D print. An OUTHIKER mount* is required.Print details:Print with supportsIncrease Perimetersuse brimI have used PETGYou will need:1 x OUTHIKER mount*2 x Cable...

This is compatible with 2010 - 2016 Panamera models (970.1 and 970.2) and is designed for my Asus ROG Phone II (hey, I said it was niche...), but could be modified easily as the phone holder body is just a box. The holder BASE and WEDGE should be...

This is compatible with 2010 - 2016 Panamera models (970.1 and 970.2) and is designed for my Asus ROG Phone II (hey, I said it was niche...), but could be modified easily as the phone holder body is just a box. The holder BASE and WEDGE should be...

Introduction ========== There's no attractive and functional phone holder designed specifically for the Porsche Panamera - at least not one without adhesives or clips. This is a niche project that works exceptionally well, making it an ideal...

Cell phone holder with adjustable tilt. ...Three files for 3 cell phone widths: 80 mm, 85 mm, and 90 mm. ...I made this for myself and as gifts, then decided to sell it too.

Customized Version of the Popular Thingiverse Design: Customized Holder for Mobile Phones Created with Our Customizer App at http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Using These Settings: * Base Cutout Size: 0.8 Units * Base...

This is an adjustable tripod mount designed specifically for your cell phone. It can also accommodate an old small iPod touch and a big phone (not a tablet). The design has three distinct parts to print, making it a bit more challenging than other...

This adds the horizontal mounting configuration. ...GoPro mounting system

Below are the settings used for this customized design: Phone Size - Phone Width: 81.5 mm - Phone Height: 151 mm Grip Settings - Grip Width: 3 mm - Cross-Side Offset: 1 Clips and Holes - Clip Thickness: 4 mm - Bolt Diameter: 0 mm (Not Required) -...

... fit either vertical or horizontal. There is a gap for the charging cable to fit if you hold the phone vertical. I also included a small clip on the bottom right you can clip your charging cable to. ... This was kind of an experiment I had fun with

A custom phone dock, specifically designed for users who want a versatile and durable solution to hold their phones. Created with Thingiverse's Customizer tool. ... To use this design, you'll need to adjust the following options: - Holder width: 10...

Phone Length Set at Maximum Customization Value Customization settings were optimized using advanced algorithms for a precise fit. Using a unique combination of features to enhance performance. These specific settings are: Phone Corner Radius: 10...

I was upset at the lack of places to visibly put my phone on the dash of the old Silveraydo so I did something about it.

The instructions, printed on a MakerBot, detail how to attach an HTC Sensation phone onto the handlebar stem of a bicycle.

A device used for securely attaching a phone to a surface, typically inside a vehicle, allowing easy access and visibility while using the device.

Instructions for customizing this design are below: Using the following options, you can customize your new mobile phone holder: Phone length: This value represents how long or short you want the dock to be based on the type of phone you plan to...

Support to for phone on T3s Gamesir for Tello or other use 2 versions: - 1/4 inch photo screw hole - Flash support type

Customized Version: http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Instructions Using the following settings: Holder Height is 20 units Base Cutout Diameter is set at .8 inches Phone Holder Width is adjusted to fit standard phones up...

Print settings are up to you I guess. ...I have had success with up to 0.25 mm line thickness. you need to make 2 for a phone to sit comfortably, but you can make 4 to fit two phones :D hope you like it