post clamp 3d models
158306 3d models found related to post clamp.thingiverse
needed a post clamp for a camera cart that I built and wanted to prototype it.. here's what I ended up with. ... I made it to use a 1/4" bolt and nut (it's what I had most of)
thingiverse
Simply slide the clamp onto the seat post and secure with a M3 nut and bolt. I printed it with PLA with 10% infill to keep it as light as possible. The nut fits very tight, so you may have to press it in with pliers. ... I did this on purpose so it...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_len = 20.7 gopro_bar_screw_d = 4.7 gopro_bar_screw_nut_d = 10.55 gopro_rod_nut_th = 3.6 gopro_bar_screw_head_d = 8.9 gopro_bar_th = 7...
prusaprinters
Hi, here´s my little seat post clamp to fix my old LED rearlight. The clamp diameter is about 31,6 mm. You´ll need an additional M3 x 20 mm screw with a nut. Greetings,Köter
thingiverse
This is a 2-3/8 in fence post clamp with a channel to change out different hooks depending on the need. ...My friend and I came up with this concept to use the fences posts to place a clamp on and have interchangeable hooks for hanging things such as...
thingiverse
A friend broke the seat post clamp on her bicycle. The replacement part is on order but estimated 3 months for delivery (thanks COVID). So I made this adapter to allow a hose clamp to fit. To make it I traced around the inside of the old clamp onto...
thingiverse
This is a spacer I designed to be able to clamp 2 round fence posts together. This is designed for 1 7/8in fence posts. Use a 3in-5in hose clamp and it will make a very strong connection. Much cheaper than gate hardware. I printed at 100% infill...
thingiverse
Customized version of https://www.thingiverse.com/thing:3075868 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3075868
grabcad
Optomechanical item of Avesta LLC, Russia.Sadly, they didn't put models on their site, so at some point I had to make those for use in our projects.I don't hold any rights on Avesta's products, so, if their representative addresses me, I'll remove...
prusaprinters
<p>This is a GoPro-style mount for a Diamondback Overdrive 29er mountain bike. It should fit fine on any bike with a 35.5mm circular handlebar stem.</p><p>Customized version of <a...
prusaprinters
Compatible non-magnetic optomechanical parts: https://www.newport.com/f/molded-composite-optical-post-holders https://www.newport.com/f/molded-composite-optical-mounting-posts The part is best printed from solid ABS; apply ABS slurry to the...
thingiverse
Compatible non-magnetic optomechanical parts: https://www.newport.com/f/molded-composite-optical-post-holders https://www.newport.com/f/molded-composite-optical-mounting-posts The part is best printed from solid ABS; apply ABS slurry to the...
thingiverse
Really simple little parametric model (OpenSCAD file included) that will take your entered post diameter and make an adapter for that post to go into a vise. I used this to put a bicycle seatpost in a vise and get a firm grip without ovaling the...
thingiverse
Post-style mic clip I made that attaches to the bottom half of a standard mic clip. ...The plug in the center of the attachment hole is made for easy support removal.
thingiverse
Useful for light duty. ...The rotating one takes a 10-24 screw and nut to lock its angle and all the post holes take a (standard) short 1/4'' optic table bolt and self thread in the thicker section of PLA. ...Print it at atleast 40% -60% infill.
thingiverse
A post clamp for the Steadicam Archer (1 1/2" post) with a D-Tap hub clip. Specifically designed for the Alvin's cables D-tap splitter to Lemo power cable. ... The clip was glued to the clamp after printing, I also added a couple of pieces of tape to...
thingiverse
This is a replacement post clamp shell, for a modern Craftsman drill press with a 2 1/4 inch post. internal parts are not included, and should be transferred over from the original. ... The original part is no longer made, and does not clamp straight...
thingiverse
I designed new wedge keeping the seat on place of FirstBike. The oiriginal one broke. I went through few iterations. Nylon looks perfect now. ABS good. I tried PETG for older versions but it was breakable (cracks under load). PLA same as PETG -...
thingiverse
Customized version of http://www.thingiverse.com/thing:115211 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=115211 Instructions Using the following options:...
cults3d
This collar unlike the original is in 2 parts because when disassembling the old collars those this broke when removing them from the posts. ... Size of the collar for posts of 50x50 mm My blog on 3D printing:...
thingiverse
designed for externally routed dropper posts with 27.2 seat posts
thingiverse
I broke my desk lamp holder right at the base. ... tried to glue it back together but did not hold. Therefore I designed and printed one, nearly identical to original. Took the screw part out of the broken clamp and used it on my print.
myminifactory
Carry it with you with this seat post clamp with integrated carry link. The clamp allows you to easily, quickly, and consistently obtain the exact seat height setting when you come back to your ride after a hard day at work/school. The carrying link...
thingiverse
... This is the 3D reproduction of the 60 mm Btwin quick release clamp for bike saddle. ... It is not intended to be printed but to be inserted to illustrate a project which would use this very practical accessory even somewhere else that on a bike.
thingiverse
* The inner ridge is now smaller to not lift the clip off the pole even in a notch * The clip is now taller (20mm -> 60mm) giving the clip more grip against leverage from attachments * The 3 post variant offers a simple mechanism for hanging items...