printed double fold bias tape 3d models

This bias tape folding device improves on a standard single-fold into making two folds without out any intermediary steps; a flat strip of bias fabric inserted into one end and the other end is ready to heat & press.

Recently I used bias tape maker posted by Oscarco https://www.thingiverse.com/thing:3880491 It makes fine tape but I needed the double fold tape. So I designed this little maker. To make a double fold tape you have to iron the bias tape made by...

... on requests from people sewing straps for the Million Mask Challenge. ...It can be pinned to an ironing board to free up a hand so the bias tape can be pressed while you pull it through the guide. ...There are two version, 4 cm and 5 cm input width.

Bias tape maker (bias folding jig). ...Helps to make bias tape for masks.

This simple print is designed to fold 50mm cotton fabric into a 25mm bias tape. ...

A handy tool for making bias tape for your sewing projects. ... Available in 1 inch and 1/2 inch bias tape. If you don't want to print the bias tape maker ring, a bent paperclip could suffice.

I have some metal bias tape makers but no matter how slow I go it the fabric get's all twisted up and comes out very wavy so I was doing it by hand burning my fingers and it takes so long folding it all by hand. This is much faster and much more...

I've seen so much bias tape maker on here and wanted some small gadget to store it without it being tangled. Since I couldn't find any, heres my desing. There are no special settings I've used. Just 40% infill and a profile quality of 0.2. ... For...

Folded again (by hand) makes 10mm (3/8") wide double fold tape. The slot alot on the bottom surface is to allow the user to push the fabric towards the exit with a pin or similar. For best results, use a steam iron to flatten the folded fabric as it...

Hey, this is a bias tape former. I hope you like it. ...

This is a remix of bias tape maker from https://www.thingiverse.com/thing:3880491 by Oscarko for 4cm tape

This is a remix of bias tape maker from https://www.thingiverse.com/thing:3880491 by Oscarko for 4cm tape

a simple tool for making bias tape, simply feed the fabric strip through, and iron it as it comes out.

The smaller tape maker had really thin walls, and my machine wouldn't print them. I've thickened the walls and made it slightly different, but all credit goes to Mquin123 - thanks. ps. I've added the sketchup file, but be warned it's a bit of a...

Removed wings, because people don't need them. ...The wings limited you to putting it one direction. This way you can double side tape it down any direction you want. ...Also, removed a ton of material from the sides to save on printing expense.

... ...Reducet the mass, so the print takes about 1h10mins but when setting the nozzle temperature to 249C you can go up to 150percent of speed and so having one done in about 50minutes. ...Standard Prusa bed 25x21cm can be used for printing 30pcs at once.

Used to sew straps for surgical masks.Any filament works. ...It is printed with the side next to the ruler touching the bed.

great design i edited the size down to save on material make it print easier and faster without the numbering this also gave two holes great to add loops and make it easier to pull

great design i edited the size down to save on material make it print easier and faster without the numbering this also gave two holes great to add loops and make it easier to pull

The original is a great design and if you are only making one, make the original. ...I Reworked the design simply to save print time while mass producing them in support of mask makers. ...If possible, show support for the original design.

5 cm bias tape maker

You can order here https://www.etsy.com/listing/798388313/one-shot-double-fold-bias-tape-maker-1-1 and we'll do our best to print and ship as fast as possible. At the moment, this is not intended to generate profit, but only to recover costs while...

... have been supplied. The format is: bias_width x tape thickness x forming length + stablising length. E.g. The file bias_tool_50x1.0x50+30.stl uses 50mm cloth to make a 25mm folded result the slot is 1mm thick and the whole tool is 80mm long. ...

This is a simple half inch bias tape maker inspired by: http://stitch-n-smile.com/how-to-thursday-create-a-bias-tape-maker/ I just made a little fancier 3D version. ... I think you could upscale it if you want other sizes, but I haven't tried.

Changes - Seperated the components for printing with different infill and better use of print bed. The connectors and the fabric arm should have more infill to make them a bit stronger- I printed them at 50% infill 0.15 layer height in Material PTG...

Print it. Sew Masks! Please help support the cause. Many of us are coming out of pocket to produce this equipment. ...If you have funds available to donate, find me on facebook: @ZedAxisLLC or donate directly to my campaign, here: ...

Print it. Sew Masks! Please help support the cause. Many of us are coming out of pocket to produce this equipment. ...If you have funds available to donate, find me on facebook: @ZedAxisLLC or donate directly to my campaign, here: ...

... edges. There is also a horizontal version for ironing with a flat iron. Takes an input of 1.5" (~4cm) strip of cloth and creates a 3/8" double fold tape. Print with or without raft (depending on filament). ...100% fill, 0.2 layers, no supports.

My partner liked the ability to pin down the tool (seen in in [this bias-tape maker](https://www.thingiverse.com/thing:4292451)), so I added two more 'wings' and holes to allow you to do so. My skill level with tuning the printer is at the beginning...

... Currently being used to aid in relief efforts for COVID-19 masks! This is a remix of bias tape maker from https://www.thingiverse.com/thing:3880491 by Oscarko for 4cm tape Technically a remix of a remix since I based this on GazdaTony's model