printer for truck drivers 3d models
2379364 3d models found related to printer for truck drivers.thingiverse
This is a holder for the exceptional Koss Porta Pro driver. It should fit following drivers as well, because they are the same: PortaPro PortaPro Jr. ... SportaPro KSC-35 Pro-35A The KSC-75 Driver (PortaPro Driver with a titanium membrane) should be...
thingiverse
I had some drivers and wanted to be able to access them easily and see which is which. The handle diameter is just under 18 mm. ... I connected the pieces with M3 screws, quad copter standoffs, and a couple of nylon spacers.
cgtrader
All four drivers parked in the assembly. Already in the stage of 3D printing. ...
thingiverse
I wanted to print MrCranky's truck, but i couldnt fit the trimmed frame parts on my 165^3 Printer... ...so i fired up 123D, popped some screw holes in and chopped it up - Assembly should be self explanatory.
cults3d
I also found the holes for the drivers to be a tad too large. So I replaced the pegs with ones I use in my own models of pegboard components and made the holes smaller. I also made the lettering a bit deeper to make it more readable. This should fit...
thingiverse
I also found the holes for the drivers to be a tad too large. So I replaced the pegs with ones I use in my own models of pegboard components and made the holes smaller. I also made the lettering a bit deeper to make it more readable. This should...
prusaprinters
I also found the holes for the drivers to be a tad too large. So I replaced the pegs with ones I use in my own models of pegboard components and made the holes smaller. I also made the lettering a bit deeper to make it more readable.</p><p>This...
thingiverse
Gruppo per ventola con flusso aria direzionale verso i drivers della scheda. Abbassa la temperatura degli stepper del 50% Dopom la stama per il montaggio necessita di una ventola 80x80 mm. Fissaggio colonnine alla scheda: 4 viti M2,5 X 25 mm. 8 dadi...
thingiverse
Remixed frame to except 5mm tall driver motors.
thingiverse
http://www.lightobject.com/DSP-upgrade-kit-for-DK40-small-machine-P758.aspx It uses 3 stepper drivers (When used with Z lift tray) and I wanted a better way to mount the drivers in the machine than just screwing them to the panels inside. So I fabbed...
thingiverse
External Drivers plate for Tevo Little Monster (and mks sbase), you no need any boxes, fans, etc and can install up to 5 drivers.
thingiverse
This is for example an 18sound HD1050. ...But shoud fit also other 1" throated drivers.
thingiverse
This is a simple tool-holder designed for holding screw-drivers and such things. ...It's mounted with 2 screws.
thingiverse
Early version of an AUX panel for a rover mini cooper MPi, dont know if it will fit earlyier models. ...Friction fit at the moment for drivers side.
thingiverse
Simple no support tool holder/stand for a complete set of Wiha drivers, including one of the pry bars. ... No supports needed
thingiverse
I liked the way frapicchi designed it with 24 sides. This makes it 'grippier' than a smooth one would be. I also like the bottle top flange. This fits nicely over the rubber air line gasket. I added higher sides, a lip to keep spilling to a...
cults3d
Pile drivers for Siege Sideswipe inspired by their appearance in the episode "S.O.S. Dinobots". ...These simply slide over Sideswipe's fists using a 5mm handle, concealing the fist and creating a full-size piston head.
thingiverse
... a fan with a 3D printed holder. What do you need: 8x M4 bolt (length is up to you. About 3cm [1.18 inches] should be fine) 8x M4 nut 8x washer 1x vent from old computer power supply Print Settings Printer: GEEETech Prusa I3 Supports: No Infill: 100%
thingiverse
The cable hole is large enough to accept fairly high gauge wire, but the opening for the driver is small and you must solder the wires as flat to the driver as possible to ensure an easy fit. To ensure the enclosure properly seals I recommend...
cults3d
Air Distributor for SKR v1.3 CPU Stepper Motor Drivers. It is designed to be used with a 50x50x10mm fan. We recommend using a low noise one. It is not subject to the circuit. Double-sided tape should be used on the base that supports the fan, and it...
thingiverse
Air Distributor for SKR v1.3 CPU Stepper Motor Drivers. It is designed to be used with a 50x50x10mm fan. We recommend using a low noise one. It is not subject to the circuit. Double-sided tape should be used on the base that supports the fan, and...
thingiverse
... are all weak. This design is meant to distribute the vent evenly between all 4 stepper drivers using a 50mm-12V brushless blower fan. A stepdown module is used to convert the 24V to 12V. ...The duct is strong and no need for support while printing.
thingiverse
Enclosure for a custom board I made for connections needed for stepper driver motors. The enclosure features space for 2 fans. I printed the files listed with v1, but designed v2 based on the modifications that I manually made to the already...
thingiverse
This main controller board cooler aims to keep the original cover of the Anet A6 and provide efficient/directional cooling to stepper motor drivers and other hot components. The 50MM centrifugal fan is connected using a male to male 10CM cable. On...
thingiverse
Instructions 1) Print the holder 2) Drill four small holes on the back for the magnets 3) Attach magnets with CA glue. User kicker if needed. ...4) If the holder slides around sanding the back a little or adding a thin coat of rubber cement to the back...
thingiverse
This board is sized to allow inexpensive production from Seeedstudio (Currently 10 copies for $40 + a small shipping fee):http://www.seeedstudio.com/depot/fusion-pcb-2-layer-10cm10cm-max-10pcs-p-396.html?cPath=64_12 This is perfect for a different...
cults3d
The Wiha hex drivers are a great alternative to hex keys that are worth the money if you are constantly working with socket head screws. This tool holder fits both metric and imperial Wiha series 263 hex drivers. ... Metric Set Part # Size 26307...