printers and scanners for mac 3d models

Since I plan to put a tiny SSD drive below the Mac Mini I made an alternative version with a hole large enough to pass an USB cable through. Both designs are also available in a slightly taller (20mm vs 16mm) variant. Bed adhesion can be...

Recently got hold of a PrimeSense Carmine 1.09 scanner and wanted to have a nicer handle to hold it.

SummaryRecently got hold of a PrimeSense Carmine 1.09 scanner and wanted to have a nicer handle to hold it.

Recently got hold of a PrimeSense Carmine 1.09 scanner and wanted to have a nicer handle to hold it.

this is a calibration and verification device to validate distance measurements for 3d scanners that use range finding techniques such as lidar, or sonar, or whatever. it has flat surfaces that extend out 0.5mm from 10mm from center and to 70mm from...

This is a replacement knob for Uniden DMA Trunktracking scanners. Designed for the 15/996 line but likely compatible with many others as well. ...The boeing design is from http://www.thingiverse.com/thing:851918

I used the VESA 3mm Spaker by kubius as a base for this mount. ... This one works well for 22" LCD with VESA 75 or 100 mounting. It's designed to work with the gooseneck on a Honeywell barcode scanner, but may work with others.

You need a 4x4" washer (or similar) to give the target some weight.https://www.bunnings.com.au/macsim-100x100x5mm-m20-galvanised-square-washer-each_p0018441 And a 2" by 1/2" nut and bolt to hold it all...

knob for potentiometers and 3d printers

A keyboard tray I'm in the process of making for my Mac's provided keybaord and an OEM 10-key.

The 2 piece snap-in design is perfect for bigger wigs and for smaller printers. BONUS PART: the holder is designed with an internal tank for 2 main uses: - It can be filled with sand or heavy material to increase stability - It can be used as a...

print these off and add them to your printer, you can use them to mark you axis' towers so you never forget again update 1: print with the base down and support on (pillars worked well for me, other directions will result in lots of small support to...

This is a universall filter mount designed for 120mm PC fans for every type of 3D printers. I want to use this filter in combination with my Creality Halot One SLA printer. Because i have to use it in my flat. For the housing i used an IKEA Metod in...

Filament guide for MK2 and MK3 printers. Designed to be used when the filament spool is placed on the table behind the printer. Two 608 ball bearings are needed.</p><p>&nbsp;</p><h3>Print instructions</h3><p>I have printed it in PLA only, but other...

... by Jody Bed Scraper by JernejP. This part fits on bambu bed rotating ir around 40-15º, see pictures If you like my designs and want to contribute to my coffee addiction, a donation to buymeacoffee or paypal will be greatly appreciated.

... desktop. ...One for Mac mini that is behind the display with slot for storage accessory. Another under the display facing forward for the Apple DVD. ...There are two versions of the DVD holder, the second including a slot to also hold a USB hub I have.

... ...Allows for much easier access to both the SD card slot and micro-USB port. Version 1.2 of this bracket features tweaks to the standoff placement, larger holes for through-bolts, and a slightly narrower baseplate so as to fit in the chassis better.

... ...Allows for much easier access to both the SD card slot and micro-USB port. Version 1.2 of this bracket features tweaks to the standoff placement, larger holes for through-bolts, and a slightly narrower baseplate so as to fit in the chassis better.

Replacement bushing for AEPs.

Alien from Mac and Me Movie 1988 Nostalgic 80's retro power! ... Great Gift print.

Sculpted Mac and Me. Done in Nomad Sculpt. Inspired by the clip Paul Rudd plays on Conan every time he visit. If not familiar. search out clips on you tube. ... patreon.com/gramofunicorntacosart For more sculpts by me.

Slide in an iPad (designed for the iPad Air, although the iPad mini and possibly the iPad Pro), and connect your Mac to an external display and boom! Ready to go.The fun holes are to use slightly less plastic, although they are tougher to print and...

I lost the original film holder for my Epson V600 scanner and found a great design by cudderbup for 35mm film. I remixed the original design to be used as a size 127 film holder for 4cm x 4cm film negatives. Works great with the magnets epoxied in...

Modified the original file by removing the frame dividers and locating pegs. ...Created a new snap-in top frame, with narrow dividers, to hold the Instamatic 110 negative in place and flat to the scan bed of my Epson Perfection V370 scanner.

These holders position a Lomography Digitaliza negative carrier (either 120 or 35mm version) on an Epson flatbed scanner while also raising it 3mm so that the negative is precisely in focus. If you scanner focuses at a different height it's easy to...

KeyBoard Mac

Holder for the Prusa i3 pro B Printer. ...12mm and 18mm Version Print Settings Printer Brand: Prusa Printer: Prusa Steel Rafts: No Supports: No Resolution: 0.2 Infill: 15

... hide the screws. I included the files to print on smaller beds as well as full body and face for bigger ones if using the split ones use the quick release support. ...I use soldering iron and a offcut of filament to weld the 2 parts together.

I've made this feet for PS4 in a simple "classic" design for dual extruder printers. Of course it can be printed on single extruder printers. Central part was printed using wood PLA filament, top, bottom and symbols (circle, triangle, square, x)...

I use a variation of this spoolholder for all my printers and it works great. Due to the wide "bed" of the spool-holder the spool wobbles less than it does at the broomstick-like holders. The bolts are sunken so they can not hook up your spool. The...