printrbot z wobble 3d models

Revamp your Printrbot PLUS and LC with a revised Z isolator for enhanced printing quality. Although I noticed no significant improvement in Z banding, this modification may resolve issues you're experiencing. ...The design was created using Tinkercad...

This custom designed z-axis stabilizer is specifically crafted for a standard Printrbot Makers Kit 1405 printer. The design fits snugly onto the end of the silver rods without obstructing the Z movement of the printer. For added security, two M3x10...

This modified PrintrBot base, designed for a larger setup with 12mm Z rods and LME12UU bearings from VXB, features edgier styled parts. The X-axis travel is slightly reduced to accommodate the 12mm hardware, while Z rods sit deeper in the base. Print...

I had to replace my Printrbot Simple Metal's imperial 1/4" Z-rod and z-nut due to failure of the Delrin z-nut, and it seems that Printrbot no longer sells this part. This adapter allows me to mount a 8mm trapezoid's brass z-nut onto the printrbot,...

I replaced my Printrbot Simple Metal's imperial 1/4" Z-rod and z-nut due to failure of the Delrin z-nut, as Printrbot no longer sells this part. I needed a mount for an 8mm trapezoid's brass z-nut on the printrbot. This mount positions the z-nut...

Upgrade your Printrbot with a 5mm Z-rod for improved edge waviness reduction, making it a must-have accessory. Both items have been printed using a 5mm Z-rod and demonstrate superior quality. Ensure correct firmware updates based on thread count for...

In the Printrbot Simple Beta, this text outlines a solution to install a Z-Axis limit switch under the Y/Z carriage for simpler Z-Axis homing. The recommended switch is Radio Shack Part number 275-0016; however, any similar style switch can be used.

I designed replacement laser cut holders for the Z-axis rods on my v1 PrintrBot Plus, as they were unstable due to wobbliness. I opted for 3D printable holders instead, taking advantage of their tight design fit by carefully hammering the rods into...

I recently acquired a PrintrBot Plus v2.1 and replaced the z-axis to utilize an M8 threaded rod instead of the ACME rod that it comes with. This modification enables it to operate at the same steps-per-mm as my PrintrBot Jr v1, which has been...

I recently received a PrintrBot Plus v2.1 and made significant changes to its z-axis by swapping it for an M8 threaded rod instead of the ACME rod that came with it. This upgrade enables the z-axis to match the steps-per-mm used by my PrintrBot Jr...

To secure the Z endstop screw on your Printrbot Jr., you can use this holder for the bolts. Originally, the screw would loosen and the bottom bolt would roll down, so I designed this simple solution. Although it could be tighter around the wood, it...

... to incorrect positioning. ... Print Settings Printer Brand: Printrbot Printer: Simple Black Rafts: Doesn't Matter Supports: No Resolution: Printed at .3 mm layer height Infill: 30% infill was utilized Notes: Prints with flat portion touching the table.

We upgraded the Printrbot LC's Z-axis treaded rod by incorporating a stepper motor with an integrated Acme screw. Following these instructions, print each STL file and install them on the X-Axis bridge. ...Attach Acme nuts, replace the original...

I Built My Own PrintrBot Jr Upgrade Parts - Here's What I Did When I built my PrintrBot Jr 3D printer upgrade, I faced two significant challenges: finding the correct files or designs for the aluminum blocks and locating the spacer. Determined to...

Since I switched out my original Z-axis for a newer model featuring only a 1mm thread, it became necessary to acquire an updated end to securely hold the new assembly in place. Instructions to Attach the New Mount: Printing Recommendations: This...

... by Its Original Author, Presumably Found Somewhere Within This Community. This Mounts Directly to the Z-Axis Motor Bolt, Which May Require a Longer Bolt for Secure Attachment. ...In This Case, a Spare 5mm Longer Bolt Was Utilized Successfully.

... its design was altered. I created two length options to cater to users with restricted space while homing the z-axis; I opted for the long one due to longer springs. ...The original Solidworks file is provided for further customization needs.

This thing reduces the z-wobble and guides your filament with close to no friction. ... Instructions You'll need: 2 x 608 bearings (the skateboard bearings most designs here use) 2 x M3x12 screws (just...

However, there's one catch I've encountered: when homing the printer or executing large Z-moves, the wobble on the top of the threaded rod becomes a concern. To address this issue, a stabilizer can be attached that glides over the threaded rod...

Z-Axis filament holder designed specifically for PrintrBot Simple Metal, augmented by additional support on the opposite side to accommodate IKEA's LEDBERG LED strip-light set. This DIY project consists of four distinct parts, with STL files provided...

The new plastic printrbot base keeps the z-motor stable, allowing it to move smoothly without rocking like its standard counterpart. For added stability, you can use linear bearing clamps instead of zip-ties to hold the y-bearings firmly in place.

Human: Installing an Optical Z-Endstop on the Printrbot Plus v2.0 via Mechanical Switch Endstop Mounting Holes. Instructions for Installation: Use a 3D printing setting of 3 Perimeters and 40% Infill. The optical sensor used in this project is...

Bracket for mounting an optical Z-endstop on the Printrbot Plus v2.0 using the mounting holes for the mechanical switch endstop. Instructions 3 perimeters, 40% infill I picked up the optical sensor from Amazon...

... may not last long enough. ...Two versions are available: Original: Identical to the original from Printrbot Spaced: Holes for M3 16mm screws have been adjusted for better outcomes. ... Instructions: Print: 2 perimeters 50% infill 0.1 mm layer height

Before installing my matrix precision upgrade, my existing spool holder was working perfectly fine - mounted on top of the Z rails for my printrbot. But after upgrading, it ended up nearly a foot off the print bed, drastically increasing the...

I've been using a holder that mounts on top of the Z rails for the printrbot. That worked great until I installed my matrix precision upgrade. Now the Spool Holder is sitting nearly a foot off the print bed drastically raising the center of...

You'll need: - M6 threaded rod - 2 x M6 nuts - 2 x M3 x 16 socket head cap (You might have extras from your Printrbot Simple kit.) - A spring suitable for an M6 rod with an OD smaller than a M6 nut. Note that the anti-backlash feature may require...

Mechanical Support: Custom-Made Endstop Holder for Z Axis on a MakerBot-Style 3D Printer

Install a Stock-Z-Nut on your 1/4-16 inch ACME lead screw.

Still have 3mm filament that you want to use with your Printrbot Plus v2.1 with the Z-X Upgrade? This adapter replaces the standard baseplate (using Direct Drive extruder) with one that lets you mount the tried & true Wade's Extruder. I created this...