professional drag chain cable changeable in scad width height 3d models

This is my take on the X Axis cable chain and necessary attachment pieces. ... The image above outlines all the parts to print and direction for assembly.

Parts to add a 10x10mm cable chain for X wires (module wire and air assist pipe). ... Also needed two M3x20 bolts with nuts and washers

This is the revised version of Jaylouisw's entire printable cable chain, now featuring the previously absent 25th link. ...Simply adhere to his established printing guidelines.

Cover for profiles 2020 for cable chains ================================== With the Voron, two cable chains run directly on the 202 profile. Problem with this: The chains are fastened quite far away and tend to slip off the profile easily and there...

I redesigned the model for that specific cable channel from Thingiverse (https://www.thingiverse.com/thing:2208675) because I wasn't happy with its cable chain dimensions. BEWARE! ...The end connector might snap off.

Tray cable chain for Hellbot Magna 2. With adapter to prevent the cable from getting stuck with the tray motor. ... Print at least 4 ChainLink with cover and adapter.

**Step 3:** Un-solder the x axis sensor in order to run the cable through the chain. **Step 4:** Drill a hole in the carriage for the x axis sensor. (This is already done on the V2 version.) **Step 5:** Feed the cables through sections of four...

I required a custom mount to connect my cable chain on the motor side and X-carriage so that it wouldn't interfere with "The Hulk" supports. These mounts will shift the cable chain towards the back along the Y Axis. ...You'll need to detach your...

Chain designed specifically for Creality Ender-3 with sturdy Y and XZ axis cable mounts built in. Key benefits: Compact, rugged fasteners for standard components ensure ease of assembly and maintenance. The kit includes: Chain link module. Y up...

This chain system manages cables from the hot end to the right stepper motor located near the x-home position on the z carriage, collects x home switch and x stepper cables, and routes them through a secondary chain to the Uno. Two chains are used:...

I creatively modified 2 chain links for the front and back sides of the cable chain. I printed one of each. Additionally, I printed 18 of diogosantos88's standard links and clips for the Pro and ddemeterco reports 26 for the Max. The link with the...

Drag chain credits goes to https://www.prusaprinters.org/prints/40345-fully-parametric-drag-chain Drag chain end stop credits goes to https://www.prusaprinters.org/prints/104140-end-connectors-for-the-fully-parametric-drag-chain I printed...

This is another remix of the base place for the Aquila cable chain... the clip in version goes in well but is not so easy to take out and clean or adjust. I Also prefer bolting my parts on as it makes removal or tweaking much easier. So this is a...

... build plate only. Everything else can be printed without rafts/support. Need to drill two holes in the base in order to attach it. Cable mount on the base is angled at 10 degrees to give a little bit more bending radius. ...I've used 20 key chains.

... chain is realy good design for Anet a8 printers. But if you use the autolevel device with inductive sensor, we don't need z end-stop support on the Cable Chain X Motor Mount. I design a mount without the support. ... Thanks for comments and likes :)

... Mount one on GeekDrive and use strong double side tape or glue second one to x endstop cover. ...Print ~20 links. GeekDrive: https://www.thingiverse.com/thing:4463679 Cable chain: https://www.thingiverse.com/thing:2920060

Cable chain of my DIY direct drive, I also put the STL of the chain I used. The assembly is done with the length of the ORIGINAL cables sure the Ender3 ,can be adapted easily sure the compatible printers, For fixing sure the base of the printer 4...

Share this mill-able cable chain file designed for 3D milling with a single linked component; it's currently configured to be milled from 1/4-inch-thick material. The cable chain is suitable for use with reprap and cupcake 3D printers. ...Feel free to...

... chain to my micro swiss hot end. ... It is a very simple wrap around device that works with Slim X Axis Cable Chain with Extruder and Hotend Mount for Ender 3 Pro by norp April 27, 2020. I used bits of the hot end mount and customized it to fit. ...

To get this cable chain, you'll need to purchase one from Amazon at the following link: https://www.amazon.com/dp/B00KBPQIBE?psc=1&ref=ppx_yo_dt_b_asin_title_o08_s00 Additionally, you will require two screws that fit securely into an aluminum...

... However, when using an auto-leveling device with an inductive sensor, you can actually do without the Z-end stop support on the Cable Chain X Motor Mount. ...I took it upon myself to create a mount without this support and it works beautifully!

After experimenting with multiple cable chain designs, I found none that met my requirements, so I created my own, drawing inspiration from others in this community. To accommodate the extended Y axis beyond the original printer's limits, I...

Designed specifically to terminate the cable chain right where the wires naturally diverge just below the extruder stepper motor, it also doesn't obstruct any filament guides you might have already installed. It lines up perfectly with this Z-Axis...

To construct a large 6ft x 4ft laser cutter, a cable chain solution is required for the X axis. This necessitates an elevating and mounting mechanism for the chain on the moving assembly and a stationary mount for the beam component. ...Utilize VHB tape...

A few build tips: You will need to flip the direction of the first chain link that attaches to the right or left side of the frame so that the chain bends in the correct direction (depends on which cable chain you buy). I also recommend flipping the...

This is a modified combination of the Extruder Cable Chain Mount(http://www.thingiverse.com/thing:514728) and the Bottom Link of the Open Cable Chain(http://www.thingiverse.com/thing:40918). The presented mounts have been revised to fit seamlessly on...

Standard Prusa X Axis Upgrade Features Improved Clearance A modified cable chain addon is designed to fit the standard Prusa X axis, enhancing clearance from the Y axis by lifting the body. The addition of a larger lock ensures better clamping...

Revamping the website design for Amirkabir University of Technology can be found at www.aut.ac.ir. ...This esteemed institution seeks to enhance its online presence by updating their web appearance, ensuring a user-friendly interface and an informative...

Hello all, I'm using the cable chain on my Shapeoko-X CNC mill from myHobbyCNC, and I designed a mount for it myself. You shouldn't put any holes in this design because you might need to drill them differently depending on your mounting plate. So...

As the hotend cable chain ray is too small and finally, damages the wires inside, causing the famous "T0 abnormal sensor" error, this part diverts a bit the cable chain of the axis, enlarging the ray at the usual use, i.e. the middle ! I'm trying...