prusa lack enclosure with electronics outside by 3d models

Finally finished printing my LACK enclosure. I opted to do a color change on corner pieces so that it would be colored to match the MK3. As I was building this new, and could use the larger acrylic panels without extensions, I modeled some new full...

This is a riser I created for my Lack Enclosure v1 after discovering my ender 3 v2 was a bit too tall for the default model. This gets placed on the bottom of the enclosure in place of pieces that fit on the bottom table. The slats below the door...

Human: Customized Prusa i3 enclosure modification provides extra height and accommodates dual doors. To install doors, cut glass or plexiglass into 220mm x 500mm panels. For a wall, use 440mm x 500mm glass or plexiglass. I utilized the original door...

IMPORTANT : obviously to mount these drawers it is necessary to build the lack module of my design that you can find at the link: https://www.prusaprinters.org/it/prints/41111-n3o-lack-enclosure DESCRIPTION drawers for prusa mk3s lack enclosure....

This modification has made a significant difference in the enclosure air temperature for PLA prints with doors closed - increased by 32C sustained to 36C sustained. I'm eager to try ABS prints where I have more familiarity with air temperature...

Designed to fit Ikea lack table legs and extend thier heightmultiples can stack together.2 legs and one foot  is the same height as one ikea lack leg so you can mix and match as you see fit (foot is optional) Designe to print with 5% infill...

It seems to make a significant difference in the enclosure air temperature for PLA prints (with the doors closed, just to see what happens, increased 32C sustained to 36C sustained) so I look forward to trying with ABS where I have more familiarity...

I recreated the original doorknobs from the LACK enclosure, but I included set screws to secure them in place, and I included magnet slots for 10x3 disc magnets instead of the bar magnets from the original. ...I also included a hole underneath to push...

Remixed from https://www.prusaprinters.org/prints/34419 Print instructionsPrinted in PETG with basic settings (2 perimeters and 10% infill). Set Scale Factors 10% for all prints and print the small drawer x 3. Only the larger drawer has to be placed...

Remixed from https://www.prusaprinters.org/prints/34419 Print instructionsPrinted in PETG with basic settings (2 perimeters and 10% infill). Set Scale Factors 10% for all prints and print the small drawer x 3. Only the larger drawer has to be placed...

Due to the new Black PSU shipped with Prusa's MK3S, the original mounts no longer fit, prompting me to design a custom solution.

This is an improved version of Prusa's Lack Table. ...This remix allows you to route all cables inside the table feet and the tables are<strong>not</strong> seperable anymore.</p> <p>I included a version for<strong>2.5mm</strong> and a version...

Humans need a lack of table feet with foot grippers to keep their furniture stable and secure. ...The Amazon product B07BBLGHZH is one such solution that helps achieve this goal, available at...

One for on-off printer itself, and it is immersed so you can not accidentally switch it off, and the smaller one for LED strips light inside. I put 4 LED strips around with total length 1,6 m. It is enough light now inside the box.<br/> I printed...

Essential add-ons for crafting a bespoke Lack Enclosure using 3mm MDF include precision-crafted corner pieces, sturdy shelf brackets, and decorative trim strips to conceal edges.

I bought a LED strip for my enclosure which I couldn't bent in normal orientation with the LEDs facing down.  So I created a mount for a vertical orientation. You need one small screw to fasten the mount and a zip-tie to fasten the LED-strip to the...

... need to remove the plastic connector beforehand. Additionally, I found it necessary to create a bracket for connecting an extra table to the enclosure as no such part was included. ...This new bracket is simple to attach with just one screw per leg.

I installed 4 LED strips around the enclosure with a total length of 1.6 meters, which now provides ample lighting within. Since I couldn't trust the glue holding the LED strips to the paper surface of the IKEA table, I designed and printed holders...

I wanted an electronics case to mount under my lack enclosure. This case allows enough room for the board, fan, and two buck converters (if you use them for your fans). ... The supports for the case are necessary for the lid slots and are easily...

Normally, the Original Prusa Enclosure has a cable bushing for the rear ports, but not for the front. ...I remixed the front left door to feed the USB - cable of the EINSY board to the octopi and a flatband cable to a Pi cam inside the housing.

I redesigned the LCD support brackets to shrink the entire printer's length, making it easier to fit inside a compact Ikea Lack cabinet. ...This modification effectively shortens the printer's length by 10 millimeters.

These Drawers are great but don't fit in the PRUSA MINI build volume. I wanted to use the magnets but if I scaled the model they wouldn't fit. So I did the digital equivalent of using a hacksaw and pulled out 10mm of length.</p> <p>I take no credit...

With the revamped design, the M4 screws I had for the new BLACK PSU with the MK3S no longer fit snugly into the brace, so I've judiciously widened the holes on this remake.\r\n\r\nFurthermore, I've carefully crafted notches for the lugs directly into...

... to adjust my acrylic sheet thickness since they weren't exactly 3mm as specified. ...To compensate for this discrepancy, I widened the hinges on both sides. The top and bottom hinges now feature slots with dimensions of 3.1mm and 3.2mm respectively.

... of pliers, cutters, and hex-allen keys. ...To secure the contents in place, I utilized 4x16 mm countersunk Phillips-head screws with a precise fit. ...The English and Spanish versions are now available for download as "Tool Box" or "Herramientas".

The shims are meant to be fitted flush with the wood, which means the top shims should sit between the acrylic holders and the table top, while the bottom shims fit snugly between the table leg and the acrylic holders. Shims need to be installed on...

I was looking to install an electronics case under my main enclosure. This particular case offers ample space for the board, a fan, and two buck converters - assuming you choose to use them to power your fans. ... The supports for this case are...

As you may know, a B1 is too tall to fit in the Prusa designed IKEA Lack enclosure (version 1) and their version 2 (which needs more height / headroom because of their multi-material add-on) costs a whopping 200 hours of print time because they...

As you may know, a B1 is too tall to fit in the Prusa designed IKEA Lack enclosure (version 1) and their version 2 (which needs more height / headroom because of their multi-material add-on) costs a whopping 200 hours of print time because they...

Very simple cut in the bottom with all other cable holes blocked. Edited in OnShape. ... Here's the link to it if you want to edit it further:...