prusa mk3 print fan error 3d models

(On Thingiverse since 2018, porting to PrusaPrinters.org)Handy holder for commonly used tools, yet out of the way.Strong, secure mount.Offset from the power supply as to not block any air flow.Placed to the right side of the mk3. I use it to hold...

Because hexagons are the bestagons.Simple small profile bed handle for the Prusa MK3.  Great for moving the bed without touching the build surface or getting oils from the skin on the print bed.  Especially helpful for holding the carriage...

I changed several settings for optimal print: * 0.2 layer * 3 perimeters * 40% cubic infill * slowed first layer to 20 mm/s I included a full plate for convenience. Suggested assembly: remove x mount and z motors and rods. Don't lose hex nuts that...

These are designed to be printed and glued into the lettering on the Mk3 frame to add a little flair. Version 1 prints right side up and v2 prints upside down with a filet on the back of the letters to fit the routing a little better. I just used a...

A straightforward filament guide attaches securely to the supplied spool holder of the Mk3 system.

This is a mounting structure to mount a Logitech C270 camera to the front of a Prusa MK3/s. There are two arms that slide onto the underside of the heated bed structure and a cross bar on which the camera is mounted via a mounting block. The camera...

Engineered to address the challenge of capturing a clear view of the nozzle, this innovative mount cleverly attaches itself to the existing hotend fan to peer directly just beyond it and into the nozzle. ... Make sure to carefully choose the camera...

These are designed to be printed and glued into the lettering on the Mk3 frame to add a little flair. Version 1 prints right side up and v2 prints upside down with a filet on the back of the letters to fit the routing a little better. ...I just used a...

This plate is an excellent addition to any Prusa I3 MK3, adding a practical and visually appealing touch. The tray consists of four distinct sections: the SD Card Holder, the Smooth Tray, the Rough Tray, and the Screwdriver Holder. The SD Card...

Edit: I made the hole for the rotary encoder a little bit shorter because the knob could slide flush with the surface so you couldn't press it down anymore, this won't happen anymore. This is a clean and small knob for Prusa printers.It is...

The t-nuts were from Amazon: https://www.amazon.com/Thread-European-Aluminium-Profile-Hammer/dp/B07CNJQVV3/ The M4 screws were from Amazon: https://www.amazon.com/gp/product/B07NTMSBN4/ For slicer settings the first 4mm of the feet were printed with...

I created a holder for the Prusa LCD mount on Tatara frame.LCD cover: https://www.prusaprinters.org/prints/21785-lcd-cover-mk3s-nobrand orhttps://www.thingiverse.com/thing:3270851Prusa i3 MK3S LCD supports:You can try a shorter version (not tested):...

These custom lettering decals are designed to be printed and glued onto the Mk3 frame, adding a personal touch to its appearance. Version 1 prints in standard orientation, while Version 2 flips upside down with a subtle filet on the back of each...

Compatible with the Prusa i3 MK2.5, MK2.5S, MK3, MK3S, and MK3S+ print sheets. Optional magnets can be embedded in the print for use with a metal desk/work surface.I have included G-codes for both the standard and magnet versions for the MK3S+ and...

the steps on the MK3 are a lot softer, and it happens once and a while that by pressing the knob to make a selection it shift one step and the wrong file gets selected for printing. this is mainly because te surface you handle with your finger is big...

If you're aiming to mount your MK3 onto a solid foundation, these clips will snap right into the extruded frame. To get a secure fit against your hard surface, consider retaining your original rubber mounts and relocating them to the inside. Next,...

That way you can easily connect the Pi to your 3D Printers PSU or any other device that supplies between 5V-40V. I designed 2 versions of the case, one that will fit any Prusa i3 MK3/S (see photos) and one regular case. You could use the Prusa...

I used the upgraded version in my newest version of this toolbox V2.https://www.prusaprinters.org/prints/51795-prusa-mk3s-ultimate-toolbox-v2-modularPrint instructionsI printed in filamentum PLA with .15 layer height and 100% rectilinear infill (for...

This is a versatile bed mount designed specifically for the Prusa i3 MK3. Key Features: - It securely attaches to the metal frame that supports the heated bed. - The bed mount remains at a safe distance from the heated bed. - Proper installation...

I crafted a custom Light Bar bracket specifically designed for my Mk3 using an affordable Light Bar purchased from Amazon, costing approximately $17 - the part number is B06Y3YG8PP.

Just a simple filament guide that clips on to the provided spool holder that comes with the Mk3. Category: 3D Printer Accessories

... top surface of my Prusa. ...The concept of the Bender design on Thingiverse resonated with me, but I sought a straightforward version, so I remixed it. Please share your project if you print one; it's always satisfying to see what others have created.

Designed in Onshape and printed on my Prusa i3 Mk3S+ in Prusament PLA Galaxy Silver. Use double sides 6mm self adhesive to bond to the frame and self adhesive 24v 6mm wide LED light strips. All soldered together and linked into the 24v board. ...;ules

I made this lighting kit for the MK3 because I bought a new lens to film the printing. The macro lens needs a lot more light when the aperture is set high (required to get a decent depth of field). There are a lot of files for this project, I...

I had trouble finding a camera solution that suited my MK3, so I tried designing one myself but didn't like the result. I then decided to print other people's designs and see if any of them caught my eye. After some searching, this is what I came up...

I liked denos' TUSH remix https://www.thingiverse.com/thing:2537713 on my haribo and bear, so used his onshape link to make one that fits my mk3 clone frame. ...Included a copy of his side for convenience.Print SettingsPrinter:Mk3s...

I created this lighting kit specifically for the MK3 because I recently acquired a new lens to capture high-quality footage while printing. To achieve a decent depth of field, the macro lens requires significantly more light when set at a high...

... any trouble. These custom supports were created in SOLIDWORKS 2019 and are available for download as STEP, PARASOLID, STL, and 3MF files. The 3MF file was saved using Slic3r, which will import print settings if opened with the same software.

To ensure a seamless connection between the Palette and Palette+ Outgoing Tube and the MK3 extruder, attach the Extruder Clip securely in place. ...For users of the Palette 2 model, we highly recommend utilizing this clip:...

Just got my Prusa and after a few prints, the spool holder that came with it is really bugging me. This one that I designed has a 13.0 cm rod (11.0cm functioning when factoring in arm overlap), however, was designed to add other features as the rod...