psu brackets for prusa 3d models

I designed the U-Nas spacer bracket created by patshead, but I was dissatisfied with the PSU's tendency to shift so I built this new model that can be secured in place using the screw pillars within the case. Print Settings Printer: XYZprinting da...

The PSU holder (https://www.thingiverse.com/thing:2491547) and the Tevo Tarantula Brackets (https://www.thingiverse.com/thing:1457449) are not really compatible... So I smushed them together in Tinkercad. Here you go, about five years too late! If...

PSU chassis adapter bracket for Honeywell C200 Process Controller.

This is a simple PSU mount for the bottom shell of the PowerMac G5. Its designed to work with the existing mounting holes from the stock PSU. ...Its simple to install and almost crucial when modding an original PowerMac G5 to work with standard ATX...

... fan on the power supply of a creality ender 3. ... Installation requires removing the old fan and drilling a few new holes in the metal cover of the psu. Wire for the new fan can be run through the existing fan vent to the interior of the psu.

Only a remix of the PSU mount. ...Widened to fit a generic PSU

PSU holder to mount the unit on the side of the IKEA Lack enclosure.Hardware: n°4 flat-head wood screws 5x20mmI remixed the original one for 3 main reasons:I wanted a method to remove the PSU without unscrewing any of the screws;I wanted to mount the...

Plate for ATX PSU to fit between Makerbeam slits. Or other beams that have 3mm or 5mm slits. 170x110 with 3mm and 5mm thickness. ... Screw holes slightly oversize to allow adjustment.

This is MeanWell PSU cover for Creality Ender 3 Pro. This cover is made more rigid and fits my MeanWell better. In the future I'm going to remove fan completely because of fully sufficient passive cooling. ... Enjoy!

Thanks Vileska for the original design. ... I changed the center distance of the holes from 40 to 45 to use the PSU Holder on the 90x45 profile, and increased the diameter of the holes from 8mm to 8.5mm

The holder for the PSU is versatile and can support any standard PC power supply unit (PSU). Each part of the design prints separately before being assembled using screws. ...Printing the entire unit as a single piece would require an impractically...

The MendelMax can be fitted with a cable and power switch from an ATX PSU; simply attach these components for easy accessibility. ...If required, use a file to adjust any tight openings.

Measurements are exact, if your printer is not well calibrated i would recommend to scale it up a little bit Nuts are 7mm

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/2lHzr8p4Ggd

Moza R12 power supply holder. ...Print two of these to mount this into place.

You can access the source files and images for reference to mount a fan of your choice on the PSU. I suggest installing it at the rear end. Due to limited space, you may need riser feet and mounting the fan outside the PSU. ... If you want to check...

Parts needed: 5x M3x10 hex socket screw 5x M3 T-Slot nut for 2020 extrusion profiles 2x M3x6x5 threaded inserts (use of a soldering iron required) 2x original hex socket screw (mains supply socket) 3x original hex socket screw (PSU mounting screws)...

Parts needed: - 5x M3x10 hex socket screw - 5x M3 T-Slot nut for 2020 extrusion profiles - 2x M3x6x5 threaded inserts (use of a soldering iron required) - 2x original hex socket screw (mains supply socket) - 3x original hex socket screw (PSU...

I wanted to re-use the PSU from a Tevo Tarantula on a new Hypercube, unfortunately the S-300-12 PSU is nothing like the supply in the BOM. This is similar to the original design but moves the switch to the outside of the printer and has the correct...

The RAMPS 1.4 electronics are mounted in the Prusa Mendel's lower front-left region, allowing potential use for other Arduino-based electronics due to direct attachment to the bracket. Although similar brackets exist on Thingiverse, they may not fit...

To attach this to a PSU, four tabs are designed for drilling holes in the PSU and using M3 bolts for attachment. This model is intended for the front of a CoolerMaster RS460 ATX PSU. An update: angled bits have been added under the tabs for better...

This is a mounting bracket specifically engineered for the Reprap Guru Prusa I3. The rails have been carefully crafted to seamlessly integrate with the design found at https://www.thingiverse.com/thing:905368. ...Unfortunately, my images are currently...

My anet A8 x belt thighter was a total blast and got a lot recommanded.LeftSupportV2 : for fitting ITX motherboard better, the left leg is a bit shorter since the ITX MB is the same with as the PSU.RightSupportV2 AND GpuBracket : The gpu bracket...

I decided to swap out the Ender 3 Pro's PSU fan for one that makes significantly less noise. The issue with the stock PSU on my Ender 3 Pro is its thin design, which causes heat to build up and becomes a problem when combined with the Noctua fan...

- 330 ohm for waking up the PSU - 6K8 ohm for boosting up the Power Delivery Unit up to ~15 volts - 12K ohm for tampering the Over Voltage Protection up to 15 volts. In my case, I have added a voltmeter and amperemeter to check the PSU at any time....

**No specific instructions** for the print (maybe a brim to avoid warpping) **No screws needed** **Compatible with most of the usage**, even if I designed it for a specific need Feel free to edit this design or to message me if you have an idea or a...

PSU holder for MK3sThere was no optimal PSU holder for me, so I designed my own.The holder is screwed to the rear panel of my enclosure.I designed it in two parts to avoid disconnecting the cables from the printer.You need four M3 screws 8mm or 10mm...

TAKING REQUESTS FOR FAN SIZES YOU WANT! This is a 'clone' of the original cover that's 1mm thick. I'm uploading the source files and images for reference so that you can mount a fan of your choice on the PSU. I would recommend mounting it at the far...