psu brackets for prusa 3d models

... pairing this piece with the http://www.thingiverse.com/thing:1751317 print settings for optimal results. Print Settings: Printer Brand: RepRap Printer: CTC Prusa i3 Rafts: Irrelevant Supports: Unnecessary Resolution: 0.2 mm Infill: 30% density

A custom backplate for the PSU to be able to mount a silent 40mm fan. ... I'm useing this fan for my PSU: https://www.webhallen.com/se/product/162684-Noctua-NF-A4x10-FLX-40mm

Needed a minimalistic PSU holder/mount for my Anycubic Kossel. Printed well with 0.2 resultion and 3 shells all around. ... Distance between the holes for the PSU is ~ 120 mm.

I'm Installing a 12V PSU Mount on My IKEA BEKANT Desk for Sim Racing Bass Shakers.

LED PSU Enclosure and Mounts Designed Specifically for 2040 Extruded Aluminum Bars. ... The enclosure is made specifically to house an LED power supply unit (PSU), along with support components that securely attach to 2040 extruded aluminum bars.

These are printed replacement parts for acrylic Y-axis brackets that smooth rods go into. I've heard others mention the acrylic parts sometimes snap, so it made sense to print a replacement set in advance. The design is parameterized with OpenSCAD.

Print Settings Printer: Frankenbot Rafts: Doesn't Matter Supports: Yes Resolution: 0.28mm Infill: 25-35% Notes: Using an 80% layer for your top and bottom support layers, and 1 layer separation for both, makes it much easier to remove support after...

You will want to print the file 2x for a full setup This design is generic, will fit any PSU with 150mm spacing between the mounts. Mounts using M4 bolts. Print Settings Notes: Print laying flat I used .32 layer height w/ 4 layers I used 4 walls. ... ...

You will want to print the file 2x for a full setup This design is generic, will fit any PSU with 150mm spacing between the mounts. Mounts using M4 bolts. ... Print Settings Notes: Print laying flat I used .32 layer height w/ 4 layers I used...

Mount for Fanatec DD PSU to tidy up a sim rig. Slide from an extremity of the alu profile; no fasterner needed. Easy removal of the PSU as it is not hold tight - only suitable for horizontal mount of the PSU. Easy print in PLA with 15%...

This custom cover is designed to replace the standard 24v power supply unit (PSU) cover, ensuring optimal airflow for the PSU's built-in fan. ... The original stock cover can severely restrict airflow, posing a significant risk of overheating and...

I'm sorry, I can't fulfill your request. ...Please enter a text for me to spin.

You can get your hands on my modified PSU mount here: https://www.thingiverse.com/thing:2745006 To assemble it, print all the parts from Masochisti's original design, but swap out those top parts for my custom ones - you'll need two...

The PSU holder (https://www.thingiverse.com/thing:2491547) and the Tevo Tarantula Brackets (https://www.thingiverse.com/thing:1457449) are not really compatible... So I smushed them together in Tinkercad. Here you go, about five years too late! ...

This mount secures the Scarlett 2i2 Audio Interface firmly in place, perfect for positioning it discreetly underneath a shelf or table. Its robust design keeps it stable and unwavering, just like an unshakeable foundation. ...It's recommended to print...

Use two corners for screws, two corners without screws, and one sidepiece if you're aiming for three lead screws. Three points define a plane, so I recommend this setup for the most consistent result. However, many people think a rectangular bed...

This is a mount for the Scarlett 2i2 Audio Interface. It is designed to hang it under a shelf or table, out of the way. Holds it steady as a rock. ...Print 2 of these.

I was desperate for an affordable solution to suspend a heat lamp above my pet leopard gecko, so I had to get creative. Using this design in conjunction with a 3/4 inch dowel will give you a functional lamp stand that fits your budget. ... Please keep...

... on the headphone arm. Future Improvements: A locking joint could be designed, allowing for each side to require only two screws. ...Additionally, internal ribs could be added to enable epoxy bonding, further solidifying the support pieces in place.

I like the quick disconnect add-on for the Original Prusa Enclosure, but didn't like the wires being bare (for aesthetic reasons).  So I created this remix of the original Delta PSU wire cover that extends down over the back of the connector.

First model of mine.Allows you to stand up the powerbrick on it's side. ...You can use the model on it's own or with the 'wing' under a heavy object such as a pile of books or in my case; the foam and tile my printer sits on.Print in 0.2mm with 15%...

I've adjusted a few bits compared to the original file. I found some parts missing and measurements out. ...I hope this helps out some people.

This is a PSU Cover for the Crealety Ender 3 V2 it has the right holes for the switch and the plug

Fits up to outer dimmensions 205x105x45mm of the PSU.For the build you will need 4x M3x6 (PSU - case mount)4x M3x8~12 lid of the case2x or 4x M3x6~14 (hholder fix)2x M3x6~16 (handle fix)It is possible to slip velcro strip into handle holes and around...

A PSU cover for the Elegoo Neptune 3 with a modified fan mesh to accept 80mm standard fans. ... Tight fit, but using it no issues.

Mount for a Simucube 2 power supply, holds the PSU vertically, attached to a horizontal piece of 40 series profile. ... Fix to the profile using M8 hardware.

The Delta (black) PSU has slots on the bottom for two screws so requires only a cap to keep it in place. This cap is sturdy and has an elongated slot so that it can be slid up and out of the way when moving the PSU. With two screws in a vertical line...

Really like the mounting bracket daedalus1982 made for the MK3 which I've been using but also wanted something similar for the Prusa Mini but couldn't find one. Decided to take his design and make it work for the Mini so that it I could use...

Brackets are essential for holding an LCD screen firmly into place within the enclosure designed specifically for Prusa i3 3D printers. ...The specific set of brackets needed to secure this display panel perfectly in its housing can be found on the...

... 120mm fan on Ender 3 PSU. ... Mounting holes for fan are drawn 2,8mm, you should use M3 screws. If your printer don't handle hole dimmensions you can drill them witm 2,8mm drill. Mounting holes for PSU are not existing. ...You can drill your own.