purse hook 3d models

My wife asked for a purse hook she could hang her purse on it so she would not have to set it on the floor. ... hang hook on edge of table, put purse strap in small hook

Based on the standard design of the old good https://en.wikipedia.org/wiki/Purse_hook I wanted to print one for my wife but couldn't find it so I tried to make it on Tinkercad. This is my first submit so I know there is still a lot of room for...

This is a simple hook that clips on to the center console so you can hook a purse off it. This prevents the purse from falling over and spilling out on to the floor. ... Designed for the 2015 Honda Civic.

The fact that their's has the forward angle forces the center of gravity towards the desk and thus keeps the hook on the table. The issue I fixed with it is adding the rounded surface that the bag handle hangs from and also removed the angle...

I based the shape off of https://www.thingiverse.com/thing:2269715.The fact that their's has the forward angle forces the center of gravity towards the desk and thus keeps the hook on the table.The issue I fixed with it is adding the rounded surface...

This is a hinged version of my "Purse Hook for Audi TT RS (2012)." The hinge allows the hook to fold up out of the way when there are passengers in the backseat of a sedan. I used M6 heat-set inserts (https://www.mcmaster.com/#94180a371/=178412o)...

This portable coat and purse hook follows the basic C-clamp mechanism to safely secure your purse and coat to any table up to 1.75in thick. Its small design (about 5in tall and 3.5in wide) means you can store it easily and take it with you wherever...

The perfect little hook for hanging all your bags or purses on a standard closet rod. A soft curve on the strap holder prevents leaving sharp edges on items such as leather bags. ...This part was designed to be fairly heavy duty and can hold a good...

This hook was designed to latch to either of the 10mm (diameter) rods that stem from the headrest and connect to the seatback. Specifically designed for the headrest of a 2005 Toyota Corolla CE. ...Can be printed without support. 

This multicolored portable coat and purse hook follows the basic C-clamp mechanism to safely secure your purse and coat to any table up to 1.75in thick. Its small design (about 5in tall and 3.5in wide) means you can store it easily and take it with...

Unfortunately it didn't have a convenient place to hang or place her purse while driving. She asked for a hook which can attach under the headrest to hold her bag and this is what I came up with. Rev 1 - Uses a pin to hold the halves together and...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/aLACG0BPaar

Wife pointed out similar item in a magazine so I modeled one up. Enjoy!! ...Scale up for more key storage.

This attaches to the front passenger seat headrest posts, providing a hook in back of the seat on which you can hang a purse or bag. It is quite strong and installs with two screws in a minute. The assembly is easy to remove if needed. Print Settings...

A purse hanger for use with 1" mounting tape.

Print the hook with 100% concentric infill for strength, the Venuses can be printed lighter as they don't support any weight. I used silk purple PLA, but I intend to print a new one in ABS when I get some. Once done just knock off the bumps with some...

No need to empty your items to have them accessible in the car, which this hook system, the entirety of your purse is handy - while properly caring for your purse. ...Print Settings Printer: Trinus 3D ...

Here is a purse holder hook thing that goes on right behind the seat of the car. ... All you have to do is take the head rest out slide the holder over the head holder rails and just put the head holder back in place, the holder is probally going to be...

I've printed several in PLA+ without issue. More infill would be better. I printed about 20% with gyroid pattern. ...Just be careful to look for weak points in your slicing preview depending on the pattern and percentage you use.

Simple modern table edge hook to hang a purse or bag. Designed for FDM printing. Long and short hook model included. It is recommended to add a foam pad or double stick tape where the hook rests on the table in order to prevent the hook from slipping...

Cabinet hook for Purse/Handbag Schrankhaken für Handtaschen.

I had made some seat back hooks from thingiverse for trash and my mom wanted a set that could hold her purse so I got out the calipers and took some measurements and printed this. It was designed around the headrest of a 2015 Ford Edge and the back...

Quick and easy to print, designed to make use of PETG though it should work in any strong filament. I printed @ .15 layer height with 10% infill with a lower temp PETG from YOYI. ...Works great!

This is a table hook that accommodates bags/purses that have a wider strap. Instructions Once you print it, the hook piece should be press fitted into the round piece. Optionally, you can apply glue or ABS juice before press fitting the pieces...

All Purpose Hanger. You get 4 high resolution stl variants: 1) With no holes: for double sided tape or tape magnet (0.5"x1.5" or 12mmx38mm) 2) With one top Hole: for #6 wood screw or 6/32 thread (3.5mm) 3) With two Holes: for #6 wood screw or 6/32...

Black Purse with metal details

Cute 3d purse, handbag, bag model in .STL format. Suitable for using as a keychain. I designed it from scratch and it 3d prints well with any WOOD PLA (or any other material such as GOLD SILK or regular PLA etc...). No need for supports. If you want...

Pocket Coin Purse for Men and Women It can contain up to 50 coins (7/8 coins per type) of 2 euros, 1 euro, 50 cents, 20 cents, 10 cents, 5 cents. and 2 cents. Compact, to divide coins from 1 cent to 2 euros. To save time in finding the right coin. ... ...

You may print this purse with soluble support as a completed assembly if you have a large dual extruder fused deposition modelling additive manufacturing machine; 1. dual extrusion - nhandbag1pciii.stl with phandbag1pciii(1).stl2. dual extrusion -...