pvelectronics 3d models

This is a clock case for the Frank 3 nixie tube clock kit from pvelectronics.co.uk. A wonderful clock kit, but I decided to make my own case out of PLA. This is listed on their site as the "IN-12 / IN-17 Nixie Tube Clock Kit With Tubes Included."...

Case is designed for FunKlock kit from PVElectronics : https://www.pvelectronics.co.uk/index.php?main_page=product_info&cPath=1&products_id=140 PDF Guide included Enjoy! ...

Case is designed for FunKlock kit from PVElectronics : https://www.pvelectronics.co.uk/index.php?main_page=product_info&cPath=1&products_id=140 PDF Guide included Enjoy!

This is a nixie clock enclosure I designed for the pvelectronics nixie QTC clock. ...I used a thin polycarbonate sheet that I just cut with scissors for the front glass.</p>

I bought the parts from PVelectronics. printed in PETG with 15% infill Treated the surface with 3DXTC epoxy and did a final paint job with rusty paint. ... Front and back plate are from an old wooden box

Case is designed to suit the Nixie FunKlock from PVElectronics http://www.pvelectronics.co.uk/index.php?main_page=product_info&cPath=1&products_id=140 Print Settings Printer Brand: Printrbot Printer: Printrbot Simple Metal Rafts: No Supports: No...

... clock kit I built. ... Kit from: https://www.pvelectronics.co.uk Item # IN8KITNOTU Hardware: used 3mm socket cap bolt. no tapping required. Updated the top , rotated 180 and made recessed hole .4mm deeper. ... did not update the test part.

Fits many six-digit kits, but was designed with PV Electronics' QTC kit in mind (http://www.pvelectronics.co.uk/index.php?main_page=index&cPath=21). This design was inspired by the hexagon shaped wire mesh anodes inside Nixie tubes, as well as the...

I had purchased some years ago and mostly assembled a QTC Nixie Clock kit from PVElectronics. Recently started working on it again, as I only lack the LEDs and the case to put it in to have it complete, and wanted to have it set up and running. My...

Built to fit the FunKlock from PV Electronics: https://www.pvelectronics.co.uk/index.php?main_page=index&cPath=1 This is a bit of a remix from the VFD clock I built previously, which was itself a remix from various other designs. The case design...

Instructions Nomenclature : 1 x Nixie Tube Clock ‘Nixie QTC’ from www.pvelectronics.co.uk 6 x Nixie tube IN-14 1 x 105, 2 x 102, 2 x 106, 2 x 107, 1 x 108, 1 x 109 8 x Insert type c M3 8 x Screw CHC M3-10 4 x Screw CLS M3-10 4 x Nuts HM3 12 x...

... pieces and then applied a maple gel stain to them to give them a bit more texture and achieve the look I was going for. You can find the clock kit here: https://www.pvelectronics.co.uk/index.php?main_page=product_info&cPath=1&products_id=140

  Hardware requirements:--------------------------- - Nixie Clock kit (PVElectronic.co.uk)- Power Supply 12V@500mA with 2.1mm center positive- Wires for connecting the encoders and the DC jack to the PCB- 2xKY-040 Rotary Encoder for replacing the...

Quantity 1 Nixie Tube Clock Kit (FunKlock) https://www.pvelectronics.co.uk/index.php?main_page=product_info&cPath=1&products_id=140 Quantity 2 Tack Switch Panasonic part number: EVQ-PAC09K - these replace the switches which come with the FunKlock...

This is a 3d printable case for a Nixie clock using IN-14 tubes Instructions This case has been made to fit a Nixie clock QTC kit I purchased from ebay The kit is no longer on ebay but can be found here with the tubes...

Quantity 1 Nixie Tube Clock Kit (FunKlock) https://www.pvelectronics.co.uk/index.php?main_page=product_info&cPath=1&products_id=140 Quantity 2 Tack Switch Panasonic part number: EVQ-PAC09K - these replace the switches which come with the FunKlock...