qidi support 3d models

I purchased a dial indicator to level my qidi x-plus more easyly and precisely. When I tried the holder from fdunn59 (https://www.thingiverse.com/thing:4633291) I had the problem, that material from the neodym magnets rest on the linear rails and it...

QIDI X-CF Pro Dial Gauge Holder that inserts just like an extruder to hold a dial gauge (indicator) for precise bed leveling.Any stiff filament will work.There are two versions.The first is not adjustable and should fit the vast majority of dial...

This is a mount for the TFT screen on the Qidi Tech X-One to allow you to put the screen on the side of the machine for a narrow profile area and to make the screen higher up on the machine and angled. I also included a faceplate from the front so...

This clip is engineered to securely fasten onto the right front edge of the Qidi Tech X-one's face, enabling the relocation of the LED strip vertically. The slight lip serves as a design element to prevent light from escaping through the front. To...

I wanted to add a filament runout sensor to my Qidi Tech X-Plus. This remixes an existing raspberry pi 3 case to have holes for mounting a filament runout sensor and clips to mount it onto the x-plus. Sadly octoprint isn't available for this...

Remixed from raveious's excellent Qidi Tech 1 XL glue stick holder, but sized for the UK market glue sticks which are 30mm (too big to fit raveious's design). Also I have truncated the holder to make it easier to print - I had three failures...

For the stock Qidi Tech 1, use the 48x26mm spacer. If you are using my full replacement guide tube assembly (https://www.thingiverse.com/thing:2848195) then this brings the tubes closer together (34mm, the same distance as between the two nozzles -...

Completo anche di un Ferma Cavo sempre da fissare sui Fori già disponibili sul Pannello Laterale della Stampante, con delle Viti a Brugola o a Croce M3 x 35mm. Link Cavo Prolunga USB:USB 3.0 pannello a filo cavo di prolunga con fibbia per auto camion...

When changing the high temperature hotend of my Qidi X-Plus to all metal I found a very small cooling fan (30x30mm) and decided to use a bigger on just to ensure maximum cooling for the cold end of the hotend. I had in mind that all metal hotends...

If you don't have a hole in the top rear of your printer (see picture number four under Post-Printing below) you can instead print and use the Bowden Connector: "qidi-xplus-xmax-bowden-tube-connector-1.0.stl". Just mount it to the extruder cover with...

This is a Bowden Tube Connector for the QIDI X-Plus and X-Max extruder covers. Just remove the screw from the top cover, place the connector and screw it in place with a 20 mm M3 screw. It is compatible with 6.0 mm PTFE tube, same dimension as the...

The QIDI Shadow 5.5s has a smaller functional build area than what Lychee Slicer will limit. Drop this into your print, check to make sure no objected are touching the boundary box and then delete the boundary box before printing. The Dimensions...

Part List: * E3D Titan Extruder: http://amzn.to/2k6UH5r * E3D Aero Kit: http://amzn.to/2k4iSBR * Clone Titan Kit: http://amzn.to/2zuXpEQ * Clone eBay Aero Kit: https://goo.gl/uzxsbe * Clone Volcano Block: https://goo.gl/txsxpa * Clone V6 Heat Break:...

Hercules - QIDI X-Plus X-Max Carriage for BMG & Dragon / E3D V6: https://www.thingiverse.com/thing:4780615 QIDI X-Plus X-Max Extruder Fan Upgrade: https://www.thingiverse.com/thing:4630187 QIDI X-Plus X-Max Advanced Extruder Cover:...

This is a mount for the TFT screen on the Qidi Tech X-One to allow you to put the screen on the side of the machine for a narrow profile area and to make the screen higher up on the machine and angled. I also included a faceplate from the front so...

I really dislike the bulky spool holders supplied with my Qidi Tech 1. Although they're expertly crafted and visually appealing, they don't accommodate every spool I possess. After finally disassembling the printer case to measure the stud -...

If you don't have a hole in the top rear of your printer (see picture number four under Post-Printing below) you can instead print and use the Bowden Connector: "qidi-xplus-xmax-bowden-tube-connector-1.0.stl". Just mount it to the extruder cover with...

QIDI heated bed connectors seem to have a habit of falling off. This cable stay prevents stress on the soldered connections on the heater pad. It is zip tied to the frame under the bed (3.6 x 150mm cable tie), after tilting to hook the lip at...

This mount is a design based on the principles shown in the [Qidi X-Plus X-Max Octoprint Raspberry Pi Camera Bracket](https://www.thingiverse.com/thing:4558596) by [cwills7](https://www.thingiverse.com/cwills75). The design allows the mounting of...

This mount is a design based on the principles shown in the [Qidi X-Plus X-Max Octoprint Raspberry Pi Camera Bracket](https://www.thingiverse.com/thing:4558596) by [cwills7](https://www.thingiverse.com/cwills75). It extends [my original...

These files are similar to ones originally made for the FlashForge Creator Pro but have modified nozzle positions because the QIDI Tech 1 has the center levelling screw at the rear instead of the front. Carelen notified me about this difference. The...

This mount is a design based on the principles shown in the Qidi X-Plus X-Max Octoprint Raspberry Pi Camera Bracket by cwills7.The design allows the mounting of the Raspberry Pi Camera (C) Rev 2.2 on the top of the door frame of the Qidi X-Max. It...

This will certainly work with other printers, but I made the measurements specifically for the QIDI X-MAX to allow a bed cam inside the enclosure. First thing you must know is you will need a strip of either aluminium (aluminum for the US),...

This will certainly work with other printers, but I made the measurements specifically for the QIDI X-MAX to allow a bed cam inside the enclosure. First thing you must know is you will need a strip of either aluminium (aluminum for the US),...

This thing is a fairly simple camera mount to get a Logitech C-270 to sit on the bed of a Qidi Tech X-One for recording/streaming prints. I built this model from scratch after my iPhone idea failed. This keeps the camera aimed right at the middle...

This thing is a fairly simple camera mount that lets a Logitech C-270 sit snugly on the bed of a Qidi Tech X-One for recording/streaming prints. I designed this model from scratch after my iPhone idea fell through. This keeps the camera pointed...

So, I was having problems with filament jamming on my new QIDI X-Max High Temperature hot end. It's possible that all I needed to do was raise the temperature or change some settings, but I bought a Micro Swiss hot end, found it to be 5.3 mm too...

I fell head over heels for the modular tool rail created by blueridgeline for his Qidi Tech One - it was love at first sight, and I downloaded and printed it immediately, not realizing it was specifically designed for the Tech One, not my X-Pro. The...

These files are the same as the ones I originally made for the FlashForge Creator Pro (https://www.thingiverse.com/thing:1698555), but with modified nozzle positions because the QIDI Tech 1 has the center levelling screw at the rear instead of the...

These panels are used to mount the AC Infinity Airplate T3 and control panel to a Qidi iMate-s or X-Plus. They replace the magnetic removable side panels. This gives one thermostat control of the temperature inside the print area. Tested on iMate-s.