qidi tech x maker 3d models

Modified the base model of the Prusa i3 camera mount in Fusion 360, customizing it to perfectly fit the horizontal gantry of the Monoprice Maker Select Plus. ...The modified design securely clips onto the top frame.

Well, standard Extruder is not really running smoothly without a special fan duct as well as a ribbon cable holder. I designed a new riboon cable holder. ...Fanduct as well as vent clip from Humebeam.

My print volume is 6 inches cubed, so the print itself couldn't possibly be printed in one single massive print. I broke it down into individual pieces and printed them separately. To make things more convenient, I combined all the parts into a...

I added a nut with a 50mm ring to hold the spool better. The two nuts are locked together to hold position. ...

I designed this to be small and easy to set up. Also, the changing of the carbon filters is easy and quick. The part is light and does not take too much time to print. You can reuse the original screws. ... I bought the carbon filter material in bulk...

The stock extruder cooling fan placement and flow path is terrible. There is a huge gap between fan and heatsink, and half the heatsink is blocked by PCB. Fan doesn't really do much... The HumeBeam Hercules Mod and the ChadMod are far and away...

Designed this 30mm fan shroud/adapter to concentrate the small fans cooling on the heat-pip e heatsink to help prevent heat creep on the high temp extruder. This fan mount replaces the two 9mm spacers on the 30mm cooling fan. Only additional...

Designed a trash container, that fits inside the printer. ...Print in two parts and glued together.For bottom 2 magnets 6x3mm can be used.Added a short and long version.

I made this to hold the tools included with this printer. There is a lot of unused space inside the printer walls, before I just had them laying on the bottom but they could get knocked around under the bed. ...This holder wedges between some of the...

Leveling squares for a 270x200 bed set with a 10mm inset from the edge.

What do you need: Bondtech Dual-Gear Drive for 5mm Axis (DRIVEGEAR-KIT-175-5) 1x M3x25mm for clip axis + 2x washer (thickness ca. 0,6mm) - one under the screw-head one under the clamp. 2x M3x30 for cooling-block Also i would change the...

IMPORTANT: This is a remix/update/improved version of the HERCULES carriage done by HumeBeam Changes/improvements compared to original "HERCULES" carriage: - Hotend cooling completely redesigned, tuned and optimized to utilize a 100% of the...

I made this to hold the tools included with this printer. There is a lot of unused space inside the printer walls, before I just had them laying on the bottom but they could get knocked around under the bed. This holder wedges between some of the...

a simple box to accommodate the hotend

My print volume is 5.5in cubed, so the print itself could not actually be printed in one large print. I printed each piece individually. I included them all in one file for easy export. Feel free to edit/tweak as you'd like to suit your needs. / ...

I tried Elphwrkz filament sensor case but it didn't fit my printer. ...I guessed my printer is a newer version so I created a new version for new machine.

Tested only with PLAPrinted with .4 nozzle, .2mm layer height, 2 walls and Arachne enabled.The following changes were made to the original design:Extended out the mounting hole for more room behind indicatorAdded fins to allow for repeated use...

Change Note 10/27/19 - Assembles seamlessly for enhanced stability. Assembled using three sturdy 1-1/2" minimum length 10-32 or M5 bolts and two robust hex nuts. Simply tilt the compact leg to latch it onto the underside of the handle, then position...

Simple power cable support. My dogs while playing would sometimes pull the power cable out so I needed a quick fix. ... Needed is one very small cable tie.

Printed with Nylon CFYou need to cut a slot in side of the cover to make room for the probe. Also it´s recomended to use threaded Inserts for 3D Prints to make it work. The CR Touch is plug and play.

Small Thingi to cover the hole in the acrylic cover and still use the filament on top. ... Please rotate by 90° before printing so that the tube is touching the buildplate too.

Holder for a 4010 style fan to replace the noisy 3010 motherboard fan. Does not occupy more space, cover can be closed.Buy a 4010 style fan (like this one)Slice and print the included holder (xsmart3_4010fan.slt)Turn off the printer, place on the...

Things you need.The 3D-ModelSealing tape. (I had one lying around)FAN_SPACER_v1.stlhttps://www.thingiverse.com/thing:6237118Thanks to D3adKennyAir Filter for Flashforge Adventurer 4 Series, 80x80x10mm, e.g. AliexpressYou can use the original...

2 parts for easy printing Remixed from by mistertech Thingiverse: https://www.thingiverse.com/thing:3375047 by Jelliott526 Thingiverse: https://www.thingiverse.com/thing:4794054

Had to swap out my passenger window after using scalding water to clean it, but I was careful not to let the magnets expand too much. ...It's now looking good as new, thanks to a fresh layer of transparent ABS plastic.

I just did a remix with the correct STL size so no need to resize.

Longer Spool Holder

Hi all, Due to space constrain in the office, I had to mount the filament on the side.Just looking around for spool holders and thought i should just practice 3d modeling and use the mount from another designer.2 type of spool holderUsing the...