qidi tech x one manual 3d models

Additional materials required: * 1m or 1.5m (depending on the position of your RPi) DSI/CSI 15 pin flat flex cable (please ping me if you find one with good EMI shielding) * 8x short M2.5 screws to attach the display to the adapter (should hopefully...

The original spool mount by Skiid dosent fit the new QIDI X-Plus 2 printer. This is my first remix but the mount fits great. The part that I changed was the little hook part of the mount. ...

Filament guide to fit the new QIDI X-pro 3D printer. It pulls the filament away from the edge of the spool. Also, to avoid leaping off the filament around the spindle. ...No supports needed for printing.

Filament guide to fit the new QIDI X-pro 3D printer. It pulls the filament away from the edge of the spool. Also, to avoid leaping off the filament around the spindle. ...No supports needed for printing.

Qidi X-Max Tapo C100 Mount Please only use the spot to mount your camera like I did. ...otherwise you could possibly crash your camera or damage your printer.

This is a replica of the nameplate situated at the front of the QIDI X-one2 printer, featuring an embossed logo and text that protrudes 1mm from the surface of the nameplate.

The camera from Qidi for the X series printers suffers from some pretty bad glare. ...This sub 13-minute print will make your camera look so much better. Be caution of your material choice due to internal chamber temps.

I ran in to a 40mm inner spool reel that is too small for the stock spool holder on my qidi x-PRO. ...So I made 1 to fit the 40mm spool hole

A filament holder for the Qidi X-Smart printer. Perfect for those with limited space behind their printer or who prefer to print TPU materials. ... Simply screw it into place using the original screws behind the left handle.

Filament guide to fit the new QIDI X-pro 3D printer. It pulls the filament away from the edge of the spool. Also, to avoid leaping off the filament around the spindle. ...No supports needed for printing.

I prefer using the lower filament holder for filament in my Qidi X-Max, but after a short time, the filament started rubbing against the ribbon cable during use. I couldn't find any filament guides for this area online, so I created one to solve the...

I custom designed it, and it is totally adapted to the QIDI X-PRO printer model 2019/2020. The use is particularly useful if you have set up a device to move the wire outlet away from the bottom of the printer wall with a guide. ... In all cases, the...

It also allows to connect the QIDI filament sensor (without the “+” pin as shipped by QIDI for the X-Max). Intercept PCBBecause the V4.6 mainboard doesn't connect the pin 8 of the flex cable anywhere, another way has to be be found to interact with...

This is a .stl i became from Qidi engineers to support the top cover of my X Plus 3, which was deformed due to shipping and permanetly scratching the ptfe tube while printing.Big thanks to great support from Qidi!I printed the 2 pices out of PC to...

AboutThe QIDI X-Max Modular Tool Holder is just like it sounds a modular tool holder system for the QIDI X-Max that attaches with a spring design to one of the handles in the printer.The base has two slots for attachments, I made a few different...

About The QIDI X-Max Modular Tool Holder is just like it sounds a modular tool holder system for the QIDI X-Max that attaches with a spring design to one of the handles in the printer. The base has two slots for attachments, I made a few...

This setup runs with the stock QIDI 1.8 Degree stepper, I originally purchased a more powerful .9 degree stepper but it was too long to clear on the backside; however, the stock one has been functioning exceptionally well... even with feeding the...

On my unit, one nozzle was lower than the other so Qidi instructed me to use a paper shim to compensate. That brought its own problems. I couldn't find an exact thickness shim to use, and the shim was temporary. Id have to fuss with it whenever I...

A way to mount the eSun eBox to the QIDI X-Max. As main attachment It uses the filament canal and the screw below at the back of the x-max. It all prints without supports but you'll need ~9x M3 x 10mm Screws e.g.

Print Settings Printer: QIDI X-One2 Rafts: No Supports: No Resolution: 0.3mm Infill: 50% Filament: Sunlu PLA + Notes: The goal here is strong, rigid parts since it is holding a 1kg spool in a cantilever design. At 0.3mm, each part prints in about an...

I have included photos showcasing the mount as it's positioned on the front of the printer and a photo of the camera attached to the mount, clearly displaying the printer printing a new mount for the Qidi X-Pro which will be featured next. No...

They are a generic camera that is often marketed under different names, like Ultimo, at MicroCenter.It is designed to mount in the rear of the printer, along the stamped metal rail.This was inspired by the LogiTech C270 mount by HammerAndAnvil,...

Modeling was done using Blender, while printing was accomplished with QIDI X-Plus. Before initiating the print job, verify that the scale is accurate to avoid any potential issues. ... Printing Details: Material: PLA Infill Percentage: 80% Layer...

This is a precision cutting rig for PTFE tubing that interfaces seamlessly with the QIDI X-Pro nozzle. I utilize this setup to trim Capricorn tubing to precise lengths. The capricorn cutter featured in one of the images functions flawlessly with this...

This is a spool holder to attach filament rolls on the side of a QIDI X-Max 3 printer.I created it to be compatible to the modular tool holder of @humebeam which unfortunately didnt hold well on my X-Max 3 printer (see...

A custom magnetic tool holder designed to seamlessly integrate with existing fasteners on the Qidi X-Pro printer's side. It may also be compatible with other Qidi models, thanks to its adaptable design. The offset between these fasteners measures...

"board-fan-mount-V2-10mm.stl" is for generic 40x10mm fan (ie, the stock24V Qidi fan) Stock Qidi fan sounds like a 12V fan run on 24V :p noisy Rearrange wires to make things neater and reduce wire strain. ... May need to flip the ribbon cable back up...

I upgraded my qidi x-pro to the all metal hotend. I purchased the hotend direct from Qidi and they sent me some instructions to tweak. They sent me a version of this fan duct, saying the new hotend may sit higher. For whatever reason, my nozzle...

The noticeable dip at the top of the Qidi X-Pro's build plate was a major concern for me. It appeared as though the two sides were curving inward, which only exacerbated my worry that they might not be properly aligned. ...This simple upgrade aims to...

This is an excellent foundation for the QIDI X-Pro printer. If you make any enhancements, consider remixing or leaving a comment here to inform others about your changes. Update 2018-07-20: Calibration tweaks were made to retraction and extrusion...