qidi tech x one manual 3d models

Changes:Added a window below the PCB holder where cables can be routed through instead of around.Other very minor aethetic fixes.Hotend mounts updated to 1.1, minor fixes.Fan duct updated to 1.3.1, minor fixes.New: Added Zodiac x Phaetus hotend...

This Project Designs a Handy Headphone Hanger Specifically for Xbox One Original and Xbox One X Consoles. In order to 3D Print this design, you will need a printer with a layer resolution set at .2mm, along with 15% infill percentage. ...Additionally,...

Icarus 2 has been released which is the current version and it has a number of improvements:View Icarus 2 hereUpdate December 21, 2021: Icarus now supports the new Orbiter 2.0 extruder. If you're already using Icarus with Orbiter 1.5 or Sherpa...

Icarus 2 is a strong, lightweight and dimensionally accurate one-piece carriage for the QIDI X-Max, X-Plus and I-Mate (and I-Mate S) that was designed focusing on strength and ease of maintenance while keeping it very lightweight.Icarus 2 is based on...

Changes:Added a window below the PCB holder where cables can be routed through instead of around.Other very minor aethetic fixes.Fan duct updated to 1.3.1, minor fixes.Hotend mounts updated to 1.1, minor fixes.If you printed 1.2.0 already there is no...

To setup a CURA Profile for your QIDI X-Max, download the X-Max.3mf and open in CURA as a project. Please save the attached file to your USB drive, do not put them in the folder. Then proceed with the instructions below to update: 1. Power off...

This should also increase performance a little.Two new versions without dial indicator holder for those who don't use them.Increased the diameter of the limit switch plate a little (the one in front of the blower / turbo fan).AboutThis is an advanced...

... I made this to install to the cover for my QIDI X-Plus and X-Plus II. I always print PETG so the covers are always on. The mount consists of a threaded top and bottom piece. The Fire Stop unit slides up into the top mount from the thread side.

AboutThis is a Bowden Tube Connector for the QIDI X-Max, X-Plus and I-Mate (S) printhead covers. Just remove the screw from the top cover, place the connector and screw it in place with a 20 mm M3 screw. It is compatible with 6.0 mm PTFE tube, same...

This is a filament runout sensor housing for the QIDI runout sensor. Placement on XMAX is far from ideal. This moves it to the top cover for a better feed angle.</p><p>Disassemble the sensor casing (torx screws I believe) and place it in the housing....

If you once update your system with a qidi provided update, all changes will be overwritten! If the printer is running well keep the following in mind: “Never change a running system!”Important note: do not restart your printer during these 7...

This is a remix of humebeam's great cover for the hole in the lid of the X-Plus and X-Max. I already had 3 inch flexible duct and 80 mm fans on hand so I remixed it to work with those. It could probably be more efficient in terms of airflow, but I'm...

Insta360 One X RC Mount

This is a X-Rite i1 pro v2 support for manual calibration table. Printed with supports but you need to sand it a bit. ... (i didn't try to print it without supports) object dimension : mm Warning : this support is for X-rite i1 Pro v2 !

... this design, as PLA will snap in the latch area. Printer settings using an X-Plus: -50% Grid infill -4 perimeters/walls -your choice of support Vent Fan: https://www.amazon.com/gp/product/B00G059G86/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

It uses a M3 x 10mm cap head screw. The belt tensioner is remixed from www.thingiverse.com/thing:1780636 and added into the carriage design. See the original thing, https://www.thingiverse.com/thing:3994628 for all the details necessary to use...

It uses a M3 x 10mm cap head screw. The belt tensioner is remixed from www.thingiverse.com/thing:1780636 (http://www.thingiverse.com/thing:1780636) and added into the carriage design. See the original thing for all the details necessary to use this...

<p>to have the write friction please print with 4 walls 50% infill petg or abs.</p><p>please use support, you can remove them with the help of a cutter</p>

Xbox One X vertical stand. ... This stand will only fit an Xbox one x stand in a vertical position and only on the side with the power on the button. ... Actual Xbox one x dimensions were used for this design.

... X button. ...(Xbox one controller)Made this because I ruined my X button and needed a new one. Tested on a PDP afterglow Xbox one controllerClicks just as well as the original buttonthere are 2 designsWith X on top of modelWith X sunken into model

Xbox One X vertical stand, effortless to print, requires two units.

I remixed it to fit my Xbox One X onto wall. ... Will update, when finished printing and hanging.

FOR QIDI TECH X-Plus 3 Implementation: I have designed a filter for air purification during the printing process, which has not yet been tested in action. The filter's volume was chosen to be roughly similar to those used in Bambu printers. The...

For those wanting to upgrade but don't want to reprint the whole carriage a remix will be uploaded shortly.Cutout for easier inserting the front mount heated insert.Minor aesthetical fixes.Print files hosted externally.The new mounts are also...

I created an adapter with the Fuji X-mount for Nikon or Nikkor Lenses. I tried to reach a tight fit through some test printing with PETG and I am pretty happy with this version. Next to the stl file I am also adding the 3dm file if someone wants to...

Support for the Insta360 One X 2 camera to be fixed on a cable for amazing effects. ... Bonus: Printable TPU Lens Protectors Video: https://youtu.be/x4GBBQ11FY0

Battery Case for Insta360 One X 360 Degree Camera - Files Now Available for 2, 3, and 4 Compartments. ...Download and Take Note of the Specifications!

This is a simple pad for the Xbox One S and X. ... Print in PLA 0.12mm with Ender 3 Pro and double sided tape on the console

This is the protective lens cover specifically designed for the Insta360 One X, drawing inspiration from the creative vision of Roland Med at medelis.se.

I found DC010's design and realized it was what I wanted for mounting my Xbox One X to the back of my TV that is on a cart. All I've done is expand the mount to fit a One X snuggly. ... Just print two and screw them to your VESA mount or through the...