qnap key 3d models

I lost the key to my QNAP NAS device and was unable to find either a spot to buy one at a reasonable price or a 3D print online. Using some calipers, I threw something together real quick that got the job done. ... I printed on the side at 0.15mm layer...

Lost your Qnap Drive Bay Key? I did and I couldn't find one that fit out there on the internet tubes.... So here one is! Print vertically upright with key indent on bottom for strength. I used 85 degrees for supports so it didnt do any inside...

Halterung 'QNAP-453A Remote

A remix of the excellent QNAP TS-341P tray with thinner sides to fit in the QNAP TS509-Pro Original: https://www.thingiverse.com/thing:3438023

QNAP Network Attached Storage 3d model. ...Included files: 3dsMax2010; Obj; Fbx

http://www.thingiverse.com/apps/customizer/run?thing_id=749887 Instructions Using the following options: fontname = Yesteryear textstring = Qnap TS219 RoundedBase = 1 wall = 1 base_radius_add_percent = .1 do_shift_font = yes textsize = 30 textheight...

Wall holder for NAS QNAP TS-112.

Support for raising QNAP TS453 mini

19" Rackmount for QNAP 10Gbit Switch

... the switch into it. It sticks out a bit, but there's plenty of airflow to keep things cool, and it gets things out of the way. I've designed this for the shape/size of both the QNAP QSW-308-1C, and the QNAP QSW-M408-4C (both pictured). ...

... of http://www.thingiverse.com/thing:1038261 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1038261 Instructions Using the following options: xTranslate = 50 wholeMessage = qnap/ts x zRotation = -45 zScale = 10

19" Rackmount for QNAP 10Gbit Switch Print Settings Printer Brand: Prusa Printer: Mk2.5sRafts: Yes Supports: YesResolution: 200 Infill: 60 Filament: 3D Jake PLA Category: Electronics

QNAP Network Attached Storage 3d model Included files: 3dsMax2010; Obj; Fbx

This is the same tray that comes with QNAP NAS devices. ...This part fits the 2.5 inch SSD and HDD drives into the 3.5 inch slot.

... RM-IR0004 remote control. ... I've made this for testing the SMuFF (https://www.thingiverse.com/thing:3431438). Use the RM-QNAP-Logo* files for the multicolor version and arrange them in your slicer as usual. ... STEP-File for remixing is included.

... control. ... I've made this for testing the [SMuFF][1]. Use the RM-QNAP-Logo* files for the multicolor version and arrange them in your slicer as usual. STEP-File for remixing is included. ... [1]: https://www.thingiverse.com/thing:3431438

The rubber feets on my old Qnap TS-210 have slowly given up over the years. Designed new ones in Fusion360 and printed them on my Original Prusa MK2 in TPU. Since it is difficult with support and flex materials a small cut is needed to the lips...

This is a wall mount for the QNAP RM-IR0004 remote control. I've made this for testing the SMuFF. Use the RM-QNAP-Logo* files for the multicolor version and arrange them in your slicer as usual. STEP-File for remixing is included. Print Settings...

Patas antivibración con muelle para NAS QNAP TS-251D / Antivibration Spring Legs for NAS QNAP TS-251D. ... Materiales adicionales / Additional parts: - 1 espiral para encuadernar Ø22 L=8-10cm / 1 spiral binding Ø22 L=8-10cm - Goma eva / eva rubber

You can use the original Screw from your Nas.

Remix of remix - the original tray nearly fit - remixed to 11 mm high to fit TS851

Remix of TS509 tray remix.

A rack shelf for your QNAP switch. I hesitate to call this a "rack mount" because it's just a shelf - not a hard mount. But it works more than well enough for me. Pictured mounted on my LACKRACK. Also holds the power brick and has a couple cable...

A rack shelf for your QNAP switch. I hesitate to call this a "rack mount" because it's just a shelf - not a hard mount. But it works more than well enough for me. Pictured mounted on my LACKRACK.</p> <p>Also holds the power brick and has a couple...

Print this with only two shells from a soft TPU. I had only 15% infill. I used only 4 top-layers @0.2mm. ... It should be soft - the better the dampening.

I constructed this Thing to change the complete HDD set in my Backup NAS. ...To mount the Cover use a Nylon 25 mm M3 Bolt and Hex Nut.

Mit 60% Infill gedruckt. Wanddicke 1,2mm. ...70 mms Geschwindigkeit

... is a model for the Gigabyte GT 1030 (GV-N1030D5-2GL). ... This is specifically made for the QNAP TS-473A. I used a 0.2mm Nozzle with PETG. ...I recommend printing this model standing upright and using tree supports for the display output cutouts.

I needed to get things back up and running so when my troubleshooting was failing, and the device was out of warranty, I decided to replace it with another QNAP (a TS-453Be). I've since decided it is working fine. I wanted to try to install...

Worked the first try (instead of requiring the expected two redesigns). For those still following along, I installed the video card with the new PCIe bracket into the QNAP. You can see the clearance with the Power connector is VERY CLOSE, but it...