quest 2 elite strap 3d models

Print one of each side headset connector and 2 of the ratchet straps at 100% infill. ...All can be fit on the print bed at the same time for an ender 3 sized bed

Was gonna grab some of the Sony ZX110 headphones for my Quest 2 and realized i had an old pair of Skull Candy over ear headphones that I remember rivaling my $200 bose set. So I remixed SolidRye's mount to use the cut up skull candy units. Give a...

Universal battery mount, you should be able to fit a wide range of battery banks on this, I'm using an Energizer 10000mah bank that can output 2.1amps. As long as you get the straps tight enough it shouldn't move around too much. ... Only thing...

I accomplished this by bending the strap up at a ~35 degree angle. I don't know if this is going to work yet. I have a few prints in the queue ahead of this, but I'll let you know how it goes once I get to it. ...I thought I'd post it up now in case...

My other design wasn't working too well so I decided to cook up something new! This is essentially a remix and combination of the two: Headphone Mod for Q2 by hadtstec: https://www.thingiverse.com/thing:4623948 Q2 Link Cable Clip by...

Just a simple remix of https://www.thingiverse.com/thing:4629958 by removing the side clip so I can adjust the tension easily. ...Download and use the other parts from the original design.

<p>My other design wasn't working too well so I decided to cook up something new!</p> <p>This is essentially a remix and combination of the two:</p> <p>Headphone Mod for Q2 by hadtstec: <a...

Cable clip for your Oculus Link cable, just snaps onto the side of your headset. This helps relieve stress of the very strained and weak USB C connector on your headset. Best printed in ABS or PETG but can be printed in PLA and will probably work...

Just a quick cable guide based on the same clip design from my CV1 headphone adapters. ...This gives you an attach point for a 4.2mm USB cable to be routed back behind you more easily.

Just a very simple, cheap and easy to print cable clip. Just slide your cable(s) in from the top. Open end makes it easy to swap cables if needed. ...Fits fairly thick cables with ease as shown.

Slip version of "Oculus Quest 2 Elite Strap_V2_NAVIDA DESIGN" for easy printing and minimal support. Glue the parts together after printing. ...

V2 of my battery counterweight for the Oculus Quest 2 Elite Strap, more secure and doesn't require velcro. The clips mechanically attach to a battery cage. This mod will triple your battery life to about 6 hours, and the counterweight will vastly...

Dual Channel Cable Clip for Oculus/Meta Quest 2 Elite Strap (With or Without battery) ------------------------------------------------------------------------------------------------------------------ * This clip has two cable channels, so it can...

Designed to be zip tied behind strap to counter weight Quest, I used some rubber pads to contact to the bracket to stop slipping maybe if printed in TPU you wouldn't need it (not tried) also used heavy duty plastic Velcro to hold battery, but have...

A new head strap design that only requires some screws (no bearings or anything special like that). You will need 11 m3 screws about 10 mm long and a bit of glue (you can also do it with 3 screw and a bit more glue). Just follow the picture and...

I haven't been able to find a universal battery pack holder for the Ozero Quest 2 elite strap so I decided to draw one up. This is designed to use velcro style cable straps to hold the holder to the head strap and small zip ties to hold the pack to...

Oculus quest 2 Fake Elite Strap Battery Holder Adapter Plate I printed the Quest battery holder and glued them together. I used blender to create this. It should take the Fake Elite Strap headband through the top hole then back through the bottom...

... supports both the elite strap and BoboVR strap from my testing. The preview is buggy for some reason on Thingiverse. I have it mirrored on prusaprinters: https://www.prusaprinters.org/prints/134337-oculus-quest-2-stand-elite-strap-w-cable-holder

... Cable" by Oculus, so it might not be perfect for this one but the Amazon Basics USB 3.0 cable fits perfectly. I got the "Cable holding" part from the "Quest 2 Elite Strap Cable Clip(s)" by Inventorlan : https://www.thingiverse.com/thing:4632370

I have remixed Wimi1s Oculus Quest 2 DIY (Elite) Strap V1.0 so that you can print it flat. It reduced the print time for me from about 4h to not much over 1h while using a lot less material for supports - with the aditional benefit of beeing less...

-------------- This is a remix of the excellent design "Oculus Quest 2 Elite Strap_V2_NAVIDA DESIGN", here: https://www.thingiverse.com/thing:4630780. I tested several designs from Thingiverse, and this was my favorite thanks to its simplicity and...

FOR THICKER 6mm CABLES Remixed version to allow for thicker cables (~6mm, e.g. the KIWI Link cable). Also added some general improvements to contouring, robustness, etc., to improve strength and longevity. Recommend printing in the pictured...

A little remix of the kreanym design, but curved a little more, I found that his model was a tad too flat for my head. ...Also with without side clips since I find them unnecessary and changed the orientation so minimal supports are needed Actually a...

<p>FOR THICKER 6mm CABLES</p> <p>Remixed version to allow for thicker cables (~6mm, e.g. the KIWI Link cable).</p> <p>Also added some general improvements to contouring, robustness, etc., to improve strength and longevity.</p> <p>Recommend printing...

Haven't printed it myself yet.

Just a remix to print easier with less supports. I just rotated it a bit and cut the lower part to lay it in the bed. Easy! Please, find the others parts in the original, https://www.thingiverse.com/thing:4629958 It works great! ...And the battery...

Just a remix to print easier with less supports. I just rotated it a bit and cut the lower part to lay it in the bed. Easy! Please, find the others parts in the original, https://www.thingiverse.com/thing:4629958 It works great! ...And the battery...

belt clip for external battery I used this model for clip https://www.thingiverse.com/thing:2041949

I liked both versions of David Navida's https://www.thingiverse.com/thing:4630780, My design of the Elite Strap for Oculus Quest 2 added box for 10,000 battery and loops for original belts. ...Supports needed.

Elite Strap by NAVIDA looked like it needed lots of support and i would rather use super glue then filament right now so i cut it into 4 parts that wouldn't require support. a and b parts 2 did require a brim but i realized later my settings were...