raise3d n2 dual
38206 3d models found related to raise3d n2 dual.grabcad
New Fan Holder for Raise3D N2 Dual for mounting at Bond Tech Extruder. ...Works fine with PETG and PETG Carbon.SolidWorks model is included: --> open "Luefterhalterung_Rahmen.SLDPRT" and have the files "Luefterhalterung25mmLuefter.SLDPRT" and...
grabcad
Optimized fan holder for Raise3D N2 dual.Model Version Rev.3Two 35mm fans + one 40mm fan for hotend cooling and two 25mm fans for nozzle / filament cooling.Improving the printing Speed and quality by increasing the hotend temperature without the risk...
thingiverse
I have a dual-extruder N2, and have little interest in using the second extruder (I wish I had bought a single-extruder). This is an improved right-side fan duct for much better part cooling when only the left extruder is to be used. It directs...
thingiverse
PB 3D Design Dual Titan Extruder For Raise3d N2 and N2+ Link to the post on Raise3D community: http://forum.raise3d.com/viewtopic.php?f=4&t=1579 Technical data: Weight with 2x Nema 17 34mm steeper motors 540g, Original extruder 879g. Total Height:...
thingiverse
Update: I just bought the N2 dual and found the print head/hot-end is identical to the N1 I had, so this will work on either model, if it has a V2 dual hot-end. I cut up and heavily modified one of the dial indicator mount brackets by...
thingiverse
I Printed this for my Raise3D N2 Dual since it did not had any spool-holders with it... These look like the original ones so when you paint the top logo it loosk almost legit. This is for the smaller (most common) spools which fits ~1000grams of...
thingiverse
I Printed this for my Raise3D N2 Dual since it did not had any spool-holders with it... These look like the original ones so when you paint the top logo it loosk almost legit. This is for the smaller (most common) spools which fits ~750grams of...
thingiverse
... N2 Plus Printer Works with Dual Head as well. ...Print Settings Printer: Raise3D N2 Plus Dual Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: .2mm Infill: 10% Notes: for best results and durability print with temperature resistant material!
myminifactory
Note: New / Better Pictures Coming I Printed this for my Raise3D N2 Dual since it did not had any spool-holders with it...These look like the original ones so when you paint the top logo it loosk almost legit. This is for the smaller (most common)...
thingiverse
Helpfull to choose offset X and Y in the printer setting for double extruder printing. ... I use it for raise3d N2 Dual + After 6 printing - i moved offset X & Y step by step. ...The calibration was good for bigger printing.
thingiverse
... shorter shaft version (65mm) for the Microcenter Inland brand spools. ... I believe eSUN and many other brands use the same spool configuration. Print Settings Printer: Raise3D N2+ Rafts: Doesn't Matter Supports: No Resolution: 300 microns Infill: 30%
prusaprinters
This thing will be discussed in detail on the 3D Printing Today Podcast: threedprintingtoday.libsyn.com or search the iTunes music store or stitcher radio for "3D Printing Today" This thing is a modification of the Raise3D N2 and N2+ bed. The bed as...
thingiverse
This thing will be discussed in detail on the 3D Printing Today Podcast: threedprintingtoday.libsyn.com or search the iTunes music store or stitcher radio for "3D Printing Today" This thing is a modification of the Raise3D N2 and N2+ bed. The bed as...
thingiverse
improved air intake for the electronics of Raise3d N2 Set scaling to 1000%
thingiverse
Modification of my desktop spool holder to fit inside the Raise3D N2 printer. ...
thingiverse
This is a smaller spool holder for the Raise3D N2 printer. ... This is designed similar to the factory holders for 1" diameter spools.
thingiverse
I was having problems with air printing on my Raise3D N2 right extruder (dual setup). I tried loosening the screws that hold the acrylic panel on the front of the extruder, but it didn't solve the problem, so I scanned and traced the panel and...
thingiverse
... default. Print Settings Printer: Raise3D N2+ Rafts: No Supports: Yes Infill: 60% Notes: You may need a raft if you see any corner lifting. ... I didn't need to scale the object at all but you may need to make adjustments if using other materials.
thingiverse
My Raise3d N2 has been very good to me, but it needs a little rise in the lid design to clear the bend in the filament tubes as they enter the extruder. I use mostly PLA, but where the N2 sits is near an AC duct and the N2 needs the lid. I made...
thingiverse
This is an Indicator Holder for a Raise3D N2 or N2 plus. It allows for indication at nozzle location for 100% of print surface. NOTE: be careful and max travel in the X Axis, holder will hit Pillow blocks! Otherwise works great! Enjoy. I have...
thingiverse
This model is something I created because one of the corners of a Raise3d Printer I am using broke. This slides well over the side of the corners, and can be secured with silicone, glue, or can be left without it. This is my first design using any...
thingiverse
This upgrade is meant to be installed on the N2 but I tried it on an N2+ Frame. It's just a bit top-heavy but rolls great on anything but thick carpet. I used the Harbor Freight 3in Casters linked here:...
thingiverse
filament funnel guide for raise3d n2 and n2 plus Use super glue after assembled Print Settings Printer: raise3d n2 and n2 plus Resolution: .15 Infill: 15 percent Notes: funnel facing up on bed including hole on retainer box
thingiverse
This is a fan grill for Raise3D N2-N2+ printers (35mm fans) that snaps very easily onto the fan's frame.
thingiverse
This is an air tunnel for the Raise3D N2 / N2 Plus for better cooling of the motion board. Inside is printed with ABS Outside is printed with Polyflex In addition, we also use a piece of activated carbon for air purification. ... www.okm3d.de
thingiverse
Simple mount for implement BLtouch into N2/N2+ Firmware mod welcome to activate BLtouch for N2/N2+https://www.facebook.com/sylvain.blt/videos/1821384614746321/ Instructions: 1- install the BLTouch as described...
thingiverse
... this as a precaution so it doesn't happen again. Print Settings Printer: RAISE3D N2+ Rafts: Yes Supports: Yes Resolution: .15 Infill: 25% Notes: I used RAISE3D PLA at 205 degrees. ... Custom Section
thingiverse
... longevity, but so far my ABS printed part seems to be holding up ok after about 30 hours of printing. I will replace it as soon as I finish machining the permanent mount. NOTE: This only works with the single extruder version of the Raise3D N2/N2+.