raise3d n2 plus

I'm having issues with air printing on my Raise3D N2 right extruder, which is set up in dual mode. Initially, I loosened the screws holding the acrylic panel at the front of the extruder, but that didn't resolve the issue. So, I scanned and...

I've been very pleased with my Raise3d N2, but it's time for a slight upgrade in the lid design to accommodate the bend in the filament tubes as they enter the extruder. I primarily use PLA, but due to its proximity to an AC duct, the N2 requires a...

... profile. Printer Settings: Raise3D N2+ Raft: No Supports: Yes Infill: 60% Notes: You may need to use a raft if you notice any corner lifting. ...I didn't have to scale the object, but adjustments might be necessary when using different materials.

This model is something I created because one of the corners of a Raise3d Printer I am using broke. This slides well over the side of the corners, and can be secured with silicone, glue, or can be left without it. This is my first design using any...

This upgrade is meant to be installed on the N2 but I tried it on an N2+ Frame. It's just a bit top-heavy but rolls great on anything but thick carpet. I used the Harbor Freight 3in Casters linked here:...

This is a snap-on fan grille designed specifically for Raise3D N2 and N2+ 3D printers, featuring 35mm fans that attach securely to the fan housing without any hassle.

... cables from disk drives, so I made this as a precaution to prevent it from happening again. Print Settings Printer: RAISE3D N2+ Rafts: Yes Supports: Yes Resolution: .15 Infill: 25% Notes: I used RAISE3D PLA at 205 degrees. ... Custom Section

Simple Mount for Implementing BLtouch into N2/N2+ Firmware Mod Welcome: Activate BLtouch for N2/N2+ Instructions: 1. Install the BLTouch as described at http://forum.raise3d.com/viewtopic.php?f=4&t=1030&start=20. 2. Upgrade the firmware by loading...

Print Settings: Printer: Raise3d N2+ Rafts: No Supports: No Resolution: 200 micrometers Infill: 100% Notes: Bed offset is set to (2,-10) despite the origin point being precisely at the left front corner. This adjustment must be made in Advanced...

This is a representation of the high-end Raise3D N2+ 3D printer in its full size configuration.

... to prevent spool contact with the printer. ...Print Settings: Printer: Raise3D N2+ Rafts: No rafts are required Supports: Spare supports; it doesn't matter Resolution: 0.2mm resolution is optimal Infill: 15-100% infill rate, depending on requirements

Multiple revisions are available for the project Titan extruder STLs, specifically designed for use with Raise3D N2 machines. ...Check out this detailed guide to follow along: http://forum.raise3d.com/viewtopic.php?f=4&t=636

PB Dual Titan Extruder Upgrade for Raise3D N2 and N2+ Link to Post on Raise3D Community: http://forum.raise3d.com/viewtopic.php?f=4&t=1579 Technical Data: Weight with 2x Nema 17 34mm Stepper Motors: 540g, Original Extruder: 879g. Total Height:...

Room air conduit enables efficient cooling of the motion control module within the Raise3D N2 system. ...Minor adjustments may be required to accommodate larger fasteners due to initial small hole diameters.

User Settings: sricam SP009 Print Settings Tab: Printer: Riase 3D N2+ Raft Settings: No Rafts Required Supports: Enabling Supports for Complex Prints Resolution: Set to Precision 0.2 mm Resolution Infill Patterns: Configuring Infill at 10% Density

Designing innovative components for the hot-end and part cooling systems requires a detailed model of the N2 print head's crucial area. ...Unable to locate a suitable model, I took matters into my own hands and created one myself.

Print Settings Printer: Raise3D N2 Rafts: Don't Bother Supports: Yes Resolution: 0.2 Infill: 15 Notes: 4mm holes are added in the rear bump out to enable M3 x 5 push fittings. The handle fits snugly into the acrylic door cutout. In the picture, you...

This is a universal adapter to accommodate the Raise3D N2 printers specifically fitted with the Mosquito Hotend from Slice Engineering. Recommend CNC Machining using AL 6061-T6 or possibly Brass C360 with Electroless Nickel Plating. ...The Mosquito is...

This is a universal adapter to accommodate the Raise3D N2 printers specifically fitted with the Mosquito Hotend from Slice Engineering. Recommend CNC Machining using AL 6061-T6 or possibly Brass C360 with Electroless Nickel Plating. ...The Mosquito is...

This block can be printed to hold the Extruder temperature probe and heater bar out of the way on the Raise3D N2+ dual printer. We found that the dual extruders were causing a lot of layer shifting issues. By removing the second extruder, this...

**SUPERSEDED: https://www.thingiverse.com/thing:3440161** Noticeably, two free fan plugs on the Raise3D N2 printer are available for utilizing additional fans. Possibly, some gapping will be required to accommodate the limit switch; however, I'll...

This is a model of the large format Raise3D N2+ Print Settings Printer Brand: LulzBot Printer: TAZ 5 Supports: Yes Notes: Rotate model 90 degrees on the X axis to minimize supports Category: 3D Printers

It's likely to fit other 3D printers made by Raise3d, but I haven't checked the dimensions of the slot on those machines' doors, and the N2 measures about 1.5 inches long and 3.5/16 inches wide - measure first or risk wasting approximately thirty...

... withstand heavy use and maintain consistent performance over time. Whether you're looking to create intricate models, functional prototypes, or even production-ready parts, the Raise3D N2 Plus is sure to meet your needs and exceed your expectations.

... I stuck little felt pads on each top piece, so I can just nudge the lid up and the props fall down without getting damaged. Thanks for the inspiration, Julia! Print Settings Printer: Raise3D N2 Rafts: No Supports: No Resolution: 0.2mm Infill: 25%

I couldn't find a Bearing Spool Holder designed specifically for the Raise 3D N2 that didn't require additional hardware besides bearings, so I combined models from an Ender 3 bearing spool holder and a Raise 3D spool holder. This design allows the...

Print Settings: Printer: Raise3D N2 Rafts: Yes Supports: Yes Resolution: 100 microns (whatever resolution you want) Infill: 15 percent Notes: I had to resize and attach in the slicer. Change the dimensions on the camera bracket as follows: Width:...

Focused heat sink cooling for stock hotend of the raise3d n2 series. Designed for a noctua 40x10mm 12v fan. ... ...

Introducing a new fan holder designed for Raise3D N2 Dual, compatible with Bond Tech Extruder. It functions seamlessly with PETG and PETG Carbon materials. ...The product includes a SolidWorks model: access "Luefterhalterung_Rahmen.SLDPRT" by keeping...

... the mounts and attach them to Greenlee's front fan mount found at https://www.thingiverse.com/thing:2745671. ... The pump mount leverages the existing hole on N2+ and should be compatible with other Raise3D printers that have a similar hole in place.