raspberry pi 4 ssd 3d models

... holes the case will be easier to remove from mount by pushing it one way and pulling up on the other end.  Its the flex that allows it to be mounted or unmounted. Works with this case: https://www.printables.com/model/24942-raspberry-pi-34-b-case

... on top. I added slits to the bottom for circulation. One improvement that could be made... Instead of screws for the raspberry pi, make the case pieces snap together. ...I don't have screws so the case is open a bit and doesn't look very nice.

I flattened the surfaces, and used templates to make holes and spaces for a Raspberry Pi Camera V2, 2x HC-SR04 Ultrasonic sensors (one at the front, and one at the side), and 2x 5mm LED lights used for status indications. ... Thanks to Uncle_Gru for...

This is a minimal mounting for Raspberry Pi 4B attached to RPLiDAR A1M8. I'm successfully printed it using my Ender 3 V2 using PLA and standard 0.4mm nozzle Prints relatively fast, around 2-3 hours, and the LiDAR attached very easily. It's not...

... and 5mm deep. Buy magnets accordingly. Requires two 40mm x 10mm 12VDC fans. You need to solder their wires together with proper connector to be able to connect it to raspberry pi 4b. ...Hold the fans in place with couple spots of hot glue.

This is a remix of Glaspedal's Raspberry Pi 4 Compute Module IO Board case. Many thanks to Glaspedal for coming up with the original design. I've split the model into separate STLs for printing, plus I've included variations which allow for a...

A raspberry pi 4 case. A slightly modified version of the original <a href="https://www.thingiverse.com/thing:3723561">https://www.thingiverse.com/thing:3723561</a>.</p> <p>I've added holes on the sides to have a better air flow around the CPU.</p>...

This snap-together case is specifically designed for the Raspberry Pi 4 with storage slots for three additional micro SD cards. The idea behind this design came from members of the Guild of Makers, who requested a case that would carry their guild...

This is a remix of my stacking Raspberry Pi 4 Modular Stacking Cluster Case. I've taken the clusters to new heights by arranging the Pis in a radial array of 10 per layer. The Pis are arranged with the SD cards on the outside for easy access to swap...

I designed a mounting bracket for the Raspberry Pi Pico, to mount it onto a 4-Channel relay. The bracket has 3 holes to mount the Pico with M2 bolts. ...The bolts screw right into the plastic, no threads needed.</p> <p>I use these setup as a simple...

This is a remix of my stacking Raspberry Pi 4 Modular Stacking Cluster Case. This takes the clusters to the next level by arranging the Pis in a radial array of 10 per layer. The pis are arranges with the SD cards to the outside so you have easy...

Important note: this version is deprecated Mark III here https://www.thingiverse.com/thing:4756812 and here: https://uplab.pro/2020/12/raspberry-pi-server-mark-iii/ MARK II is brand new version of my Raspberry Rack Mount...

In a nutshell the “Octoshield” HAT allows you to : - Plug a temperature sensor - Plug a 5V fan to cool the Raspberry Pi - Plug a 12V fan for your enclosure - Add an input (switch or sensor) - Plug RGB LED stripes - Plug Neopixel LED stripes -...

I used the Magic Phoenix kit for my 2.4 and the sugguested mounting position put my Pi too close to the wire ducting. ...This mount moves the pi ever so slightly and makes it much easier to remove from the rail.

I've remixed the rPI media center case in order to use it for the Raspberry model 4. The VESA mounts are availlable at the original thing-page (thing 2024251). ...

Features2 emplacements for 3.5" Hard disks, connected via USB3 to the Raspberry Pi140x25mm fan emplacement at the front for efficient cooling of the Raspberry Pi and hard drivesInternal Power-supply 5V/12VMain power switch and fuse accessible at the...

I wanted to mount my RPi 4 running Klipper where the touchscreen After printing it should slot into the touchscreen mount just fine - the Pi can be mounted using M2.5 screws or standoffs Enjoy!

The Middle Atlantic 2U FK2 is close but not quite the European DAP Audio 2U. ... Took goobag's bracket, and spliced in the Pi 4 solid from SliderBOR in TinkerCAD

Remixed Case to hold Pi 4 + Waveshare 2CH CAN + 40mm fan. Includes access hole for the screw terminals. ...Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 15 Filament: PolyMaker PETG Red ...

I did a somewhat hacky remix of the rather nice Pi 4 NES case to enable ethernet port usage. The lines don't quite match up, top to bottom, but it's close enough for me. ...Have fun!

Needed a mount for both the PI and the Fan for a klipper upgrade for the AnyCubic PredatorYou will need 4 m3 heatset inserts to mount the board to the mount

A Custom Retro 386/486 PC Tower Case Designed for Raspberry Pi 4 Created Specifically for the Dosbian Facebook Group. To Complete This Project, You Will Need: * A Full-Size HDMI Female to Micro HDMI Male Adapter * A USB C Extender (Male to Female) *...

The Argon40 Pi Fan Hat is a smart fan designed specifically for the Raspberry Pi, available for versions 4, 3B, and 3B+. This innovative device allows users to set their own temperature/fan speed curve, making it ideal for quiet desk use. No longer...

... the pcb. ...Both the Pi 3 and Pi 4 have 58mm spacing between the mainboard holes (lengthwise) so thats why it should work with the 3 and 4. ... It should just clip onto the frame and hold itself but it also has a cutout for small zip tie if needed

Summary & Assembly ================= This is the parts for a 3d printed handheld console that works with the raspberry pi 4 model b. You print the parts. Install RetroPie on an SD card. You use dupont connectors and solder to connect the...

https://www.youtube.com/watch?v=AegwvFUaUNY&t=94s Versions of the Pi 3 and Pi 4 are included. Pi 3 isn't tested yet, but should work fine. Regular version has room for a fan or a heatsink, not both. XL version gives up some of the dimensional...

Mont for raspberry 4 as LCD cover Spin-off of https://www.thingiverse.com/thing:4095160 The original one is difficult to install due the screw position. I split into 2 parts to simplify the installation. With this you can install the main case...

https://youtu.be/3SmSJCr62FE --- This is a vertical case for the Raspberry Pi 4 with the Ice Tower Cooler. It holds the Pi vertically with the HDMI and power connectors on the bottom. There are holes in the side for cable routing. There's an...

This was designed in fusion 360. This holds a raspberry pi 4 and a dc/dc converter. This is the converter I used <a...

This is a mini laptop designed and printed around a 5" display with an Adafruit backpack and a Raspberry Pi 4 with a cooling fan. Interference found with the screen and screen cover. Both have been revised to revision A, and are available under...