raspberry pi 4 touchscreen case 3d models

... streamlining the build process. Updated 7/18/19: Refined design incorporates user feedback. Changes include: - Upgraded 2.7mm holes to 3mm for added durability - Increased clearance between Pi and Case from 0.2 to 0.8mm for improved fitment

Einfaches Gehäuse für den Raspberry 4 um ihn an eine Seitenwand zu befestigen. RaspiPi4Platte1 ist für Standardschrauben M2,5x20 RaspiPi4Platte1M3 ist für M3x20 Schrauben und 6-Kant Muttern. RaspiPI4Platte1M3_4Kant ist für M3x20 Schrauben und...

Rpi4 Case, no supports.

My Raspberry Pi 7-inch Touchscreen finally arrived, and it's a beauty. However, this stunning display needs a rugged case that guards its glass surface from shattering when dropped. Those fragile screens can break easily, so I started brainstorming...

This is a stand to hold a Raspberry Pi 7" touchscreen in a portrait orientation. It holds the screen at a 60 degree angle, and allows access to all connections on the Raspberry Pi if you mount that on the back of the screen. I have seen this...

I modified case for 36 mm fan, no overheating after overclocking to 2,15 GHz. For more info see original model: https://www.thingiverse.com/thing:3723481 If you like this model, feel free to live a donation, so I can make more models. Every...

||| Zur Befestigung für das RPI 4 benötigt man zusätzlich: 4x Rändelmutter M2x4 4x Schraube M2x4 Die Rändelmuttern (M2x4) werden, mit einem heißen Lötkolben, in die dafür vorgesehenen Löcher des Gehäuses gepresst. So kann das RPI verschraubt und...

**Initial Case Top Design Fix**: The initial top design had rounded edges at the bottom and pointy edges at the top, which caused it not to fit properly with the case base. This was pointed out by Benjamin Summerfield. A new version was created to...

Just litle bit higher top mesh case to fit in my 30x30x10 fan with high connector

Rapid Prototype Case Design. Built to Snap Together Securely with M3 Screws. ...The Genius of M3 Holes Lies in Their Ability to Eliminate the Need for Supports Entirely.

I added screw tabs to the side of the case to allow it to be mounted. ...I also printed out standoff washers to use under the tabs to hold it away from the wall.

-No need to support.-I pirint 0.2 mm layer height with 0.4 mm nozzle.-You can use with screw or witout screw. If you want to use scew, it is for M2 sized.</p><p>-Fan hole for 30x30 fan. ...You can use without fan though.</p><p>-There are slots for cam...

The touchscreen stand from McMatt (https://www.prusaprinters.org/prints/15208-raspberry-pi-touchscreen-stand) is great, but unfortunately only for one orientation of the screen.I have adjusted the support lip of the screen and the mounting points so...

This is a stand to hold a Raspberry Pi 7" touchscreen in landscape orientation. It holds the screen at a 60 degree angle, and allows access to all connections on the Raspberry Pi if you mount that on the back of the screen. I have seen this screen...

https://www.raspberrypi.org/blog/the-eagerly-awaited-raspberry-pi-display/ [UPDATE 2016-03-27] I noticed recently the glass on my touchscreen had slid down out of alignment with display underneath. It appears over time the heat of the display...

This project is tailored for the 7-inch touchscreen designed by the Raspberry Pi Foundation. Visit https://www.raspberrypi.org/blog/the-eagerly-awaited-raspberry-pi-display/ to learn more. A few weeks later, I observed that my touchscreen glass had...

This kit was designed specifically for screens found here: https://www.amazon.com/gp/product/B075JFHLQD/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1. As a beginner in CAD, my designs are quite basic. Each component is held together by a small...

Also required are two 18650 li-ion batteries with included RE/Discharge protection circuit module, a barrel jack, a Raspberry Pi 7inch touch screen display from Element14 (Kr), an HDMI to D-SUB converter cable (AliExpress item 32451157972), and the...

Compact housing for a Raspberry Pi 4 incorporates the Protoneer CNC Hat and official Raspberry Pi 7" Touchscreen seamlessly. The Pi and touchscreen are securely attached to the top half of the enclosure, while the CNC Hat is mounted on the bottom.

This is a remix of the Touchscreen stands created by matt448. The screen edge wasn't touching the lip of the stand. Not sure if the dimensions changed or what. I took the freecad drawing and made the following changes. 1. I move the lip up by...

Case for a Raspberry Pi and 3.2 inch Touchscreen from Joy-it (http://www.joy-it.net/tft-display-32-v2/) Requires 4x M3x30 screws Modified version of case found at https://www.thingiverse.com/thing:1535495

I redesigned the touchscreen case for the Raspberry Pi, simplifying its design to make it easier to 3D print and provide enhanced protection for the screen. ...This new version is showcased prominently in several of my YouTube videos at skyentific.

This is an ideal scenario to put to work with a Raspberry Pi and an Element 41 "7" Inch Touchscreen.

Raspberry Pi 4B 5" Touchscreen (Freenove 5" IPS Toucscreen from Amazon) case with stand (top frame made of TPU), passive cooled System due to the open design. ...I wanted an easy to print and as much as possible open case, to avoid active cooling, but...

Raspberry Pi 4 Case v4

Case Raspberry pi 4 b

Case Raspberry pi 4 b

Simple Raspberry Pi 4 case

Modified from luc_e's Raspberry Pi 7 Inch Touchscreen display case. Added a power button that I purchased on Amazon, but any switch will work: https://www.amazon.com/gp/product/B01BI6TIAM/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1. A shorter wire is...

I built a case to house my Raspberry Pi 3B+ and 5-inch Touchscreen (XPT2046) that I bought from Jaycar here in New Zealand. Using it for OctoPrint with TouchUI. NOTE: This case won't fit the Raspberry Pi 4. The Pi 4 has its Ethernet port and USB...