raspberry pi case with hard drive bay 3d models

Vanslipon‘s design with added location for the 35mm fan that came with my screen, added opening for sd card access, and made the usb/data port opening larger for the raspberry pi 4 model.

A 2-piece case for Raspberry Pi 4, with fan mount. STL is in two versions, one leaves the GPIO pins accessible, the other does not. The STL is flat and with no writing, the grid texture you see was done in the slicer, so you can do it as you prefer....

I designed a custom camera mount with a built-in holder that fits perfectly on my Raspberry Pi 3 B+ and Raspbery Camera V2. My design is heavily influenced by a similar model I found online at https://www.thingiverse.com/thing:1956623, which I really...

Raspberry Pi Enclosure with LM2596 Housing I've thoroughly dissected and enhanced a fantastic design, and I'm providing the STEP files to enable customization. ... Base Design Check out the original model here:...

Have fun! A huge beautiful looking case for you Raspberry Pi 3b+ To print this beast you need around 30-40 hours depending on your printer. What you need to print: 1x front 1x back 3x connectors What you need to assemble it: 3x bigger screws to screw...

2 M5 hammerhead nuts 30 x 30 x 7 mm fan Additional Notes: *When assembling the case to the Raspberry Pi verify that the fan screws clear the CPU heatsinks. (Screws supplied with the fan are usually longer than 12 mm.) To insure that the nuts do not...

This is a straightforward case for a Raspberry Pi Model B with a connected 3.5" Piscreen attached. --- Don't waste your filament on this just yet; the measurements are still off --- Print Settings: Printer: 3Dtje Rafts: ...

Version 1.0 Rigid piece that contains and protects a device in this case Raspberry Pi Zero W and camera. It is a compact size focused on portability. It has opening to place heatsink on the card, opening for access to the gpios and micro SD. The...

*Note: This case is designed for the Raspi 3b+ if you need a case for the 4b it is linked [here](https://www.thingiverse.com/thing:3852672).* This case is designed arround the Raspberry Pi 3b+ and provides for mounting a 30x30x7 mm 5V fan. **...

This case is a carefully crafted combination of three other Raspberry Pi cases, tailored to meet my specific needs. I was drawn to the original "Malolo" case, but its design posed a problem - it didn't provide enough clearance for the heat sink and...

The size is 92 * 92 * 60mm If you want to make this case, you need to prepare the following materials, of course I also gave a list of materials: Raspberry Pi 4B1Buy it yourselfRaspberry Pi cooling tower1Used for Raspberry Pi heat dissipation,...

This is a simple case designed specifically for the Raspberry Pi 4. It features precision-cut openings for all ports, providing ample space for adding a cooling fan. The case's lid can be easily removed using zip ties, allowing for quick access to...

This is a modified version from https://grabcad.com/library/raspberry-pi-3-b-b-case-1. A better base and to accommodate my 40x40 fan are the main goals of this design. ... Editable STL files can be accessed through the following links: ...

I'm building on VGer's innovative Raspberry Pi camera case, and I've added a corner mount to securely attach the camera to any corner - whether it's a wooden post or another structure. ...Here are my print settings: Printer: JG Aurora A3 Rafts:...

This is remix of popular Sleeve Case for Raspberry Pi. I have added two mouting holes. I have attached OpenSCAD files so it can be modified. ...Please bear in mind that SCAD file imports one of STL files provided using relative path.

A remix for hanging the Raspberry Pi behind an old monitor. I printed the clip and the case separate and clued them together. Changelog: Added a second longer clip. ...Print Settings Printer: Vellemann K8800 Rafts: No Supports: No Resolution: 0,2...

Simple Case for Raspberry Pi 4, should fit model 2 and 3 as well. When slicing, just mirror the model for the Right side. ... I have added a lid, only because I printed it in Clear PLA and the light on the Ice Tower looks good through it a night.

This is just a remixed cover for [Malolo's snap fit Raspberry Pi 3 Model B/+ Case](https://www.thingiverse.com/thing:3719217) to add 40mm fan. ...You'll need to download a bottom part from the [original model](https://www.thingiverse.com/thing:3719217) ...

Remix of Ascardia's design, but for use with the following USB3 to SATA adapter https://www.ebay.co.uk/itm/334725831985

The temp of my Pi went from 60C with idle no fan to 35C under load with the case and fan. For printing, the fan holder and top do not require anything special. I used a slow first layer to make sure the grid sticks well for the top case. It's...

The temp of my Pi went from 60C with idle no fan to 35C under load with the case and fan. For printing, the fan holder and top do not require anything special. I used a slow first layer to make sure the grid sticks well for the top case. It's...

I took thing:16104 from HansH and modified it by adding studs underneath the Raspberry Pi PCB for mounting holes on Model B Rev 2. On top of the case, a slot and holes were added to mount thing:181310, which is PiPiece by dmpalmer. This creates a...

... just fine, so no nuts are needed. EDIT: Added a revised version. on my Raspberry Pi Camera v1.3, the front panel was slightly off. I don't know much about the raspberry pi version differences, but if your camera doesn't fit, try the revised file.

It's not meant to be a spaceship or a helmet with a computer hidden inside, it's just a case for your Raspberry Pi. The design was inspired by [this case by Harryb1991](https://www.thingiverse.com/thing:3735600), but I built it in Fusion 360...

This is my second Pi Zero Case designed mainly to hold my Pi Zero W , but also works with the normal Pi Zero as well if you are using wifi dongles. Its designed to allow the Pi to just slide in and the power cord keeps it in place. As it uses a...

This case is designed specifically to hold the Arduino in a convenient position just above the Raspberry Pi. It features two distinct top designs - one with a precise hole for inserting the USB, and another without, perfect for users who opt to...

This is a custom Raspberry Pi enclosure that has been redesigned to accommodate a 40mm cooling fan.

...... I've added a hole for a 30x30x7mm fan in "Rpi_4_Case_Top_30mm-FAN.stl" since the raspberry pi 4b 4gb heats up to ~62°C in idle without a case. By adding a 30mm 5v fan, I was able to reduce its idle temp to ~42°C without using additional heatsink.

However, finding a pre-made case with extra headroom for Raspberry Pi expansions is difficult, especially one with room for serial connections. This final product in the photos serves as a device server capturing serial prints and saving them as...

I really like this straightforward, simple snap case for Raspberry Pi's (https://www.thingiverse.com/thing:1572173) so I reworked the cover with my makerspace's logo (DecaturMakers.org) and then combined it with the Bitcoin logo for the RPi I use...