raspberry pi ender 3 3d models

This is my improved Ender 3 V2 Drawer to house my Raspberry Pi 4 and all the tools and spare parts that I used to store in the original drawer. Original design by bohijo1 here: https://www.thingiverse.com/thing:4604339 I shortened the drawer a...

Hi all, I purchased a Raspberry Pi 3.5" Touchscreen and couldn't find a good place to mount it easily so I went the hard way and designed myself a nice holder that fits on my Ender 3. Check out my Profile for some more Ender 3 upgrades. ### Edit:...

These can be attached to 4040 extrusion and connected directly to the main power supply via the buck converter, while also linking the micro USB cable to Raspberry Pi. That's it! No soldering is required, nor is a multimeter necessary. ... I utilized...

This is a mounting point for the Articulating Raspberry Pi Camera Mount. ... Because it has only a small mounting area it is not sufficient for heavy load.

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Filament: ESun PLA+ Black Notes: Tree supports used on the end cap. ...You'll need 4x M3 Button Head Bolts Post-Printing ============= Fitted to...

Fit my Sainsmart 5MP camera module for Raspberry Pi 3 into place. Important note: My printer is firmly fixed on a solid surface, so I haven't tested this mount with any vibrations yet. ...The joints can loosen over time, but that's easily taken care...

Camera base for https://www.thingiverse.com/thing:2842300 Designed for the Ender 3. Slots into the end of the 40x40 aluminium extrusion so the pi cam can be mounted at the rear and out the way of the build surface. Designed with enough clearance...

I made this to power my Raspberry Pi using a conventional USB cable. Just makes life easier. Can even charge your phone from your printer if the printer uses your only power outlet. I used the following USB PSU that is 12v/24v, so I've connected...

I made this to power my Raspberry Pi using a conventional USB cable. Just makes life easier. Can even charge your phone from your printer if the printer uses your only power outlet. I used the following USB PSU that is 12v/24v, so I've connected...

As for the hot bed of my Ender 3 Pro, I suppose it will also work for the standard one.\r\nThe arm has a hole where you can place a support for a Raspberry Pi camera (Rev. 1.3).\r\nThere are two possibilities: a small fixed support and one with an...

Allow the camera mount to pivot for Ender 3 Pro This is a remix from https://www.thingiverse.com/thing:4634481/remixes

I've taken the original design from Tronnic on Thingiverse, specifically the PI Trouchcase (https://www.thingiverse.com/thing:3030160), and made some tweaks to make the Pibox and frame a bit more robust. Tronnic did an excellent job coming up with...

I uninstalled the rail so I could install it on a different printer. ...Big thanks to giacomo30196 for coming up with the original concept.

This project was designed and built using Tinkercad's powerful online editing tool, accessible here - https://www.tinkercad.com/things/2uZEKkvDujs.

Remixed the Lid since I do not need access to the GPIO Header. ...and a Fan wasn't needed in my case

This design is inspired by giacomo30196's https://www.thingiverse.com/thing:3016364. A two-rail design makes the case more stably attached to the Ender3 frame. The slide-in cover locates at the bottom, avoiding screws altogether. We publish our work...

I've revamped this part to include an opening for the feed wire that connects directly to the LM2596 at the rear of the enclosure. Additionally, I've lengthened the LM2596 mounting holes as the smallest M3 screws I had on hand were too long to use.

<p>I have re-mixed this part to include a hole for the feed wire to the LM2596 in the back of the case, also increased the length of the LM2596 mounting holes as the smallest M3 screws i have where too long, also notched the two nounting pillars by...

This adapter bridges the airbox to a Mikuni TM36 carburetor, which boasts a smaller intake diameter.\r\nThe stock "96 carburetor on the Honda 400XR leaves much to be desired, and upgrading is a game-changer for the bike's performance. ...This part was...

There is hole under display for USB port and SD card reader that I've cut out since I'm using different board and display that still fits under original cover. ...Printed from PETG.

Its just a small remix with a 60mm top fan that i had in a drawer. ... I've updated the tittle because it's fitting a RPI 1 B+ too.

A simple attachment designed to clip onto the Y-axis for added functionality.

This custom creation boasts a unique blend of style and functionality, featuring a sleek new cover and a sturdy fan mount that adds to its overall appeal. To enhance the user experience, I've also designed a spacious drawer with an improved handle...

This mount is made to clip onto the metal guard over the front of the Y-axis belt. I wanted a stationary camera, capable of viewing the initial layers as well as the finished product. I also wanted it to be simple to print, with very little...

I made a tweak to the bottom part so that the inside doesn't have all those lines showing. It's a small change, but figured I'd share it with you. I didn't include the original files because [ender1968](https://www.thingiverse.com/ender1968) might...

For cura user scale it down to 10%

<p>I needed a small holder for my cam for octoprint so I made this.</p><p>The camera xy angle is 45° degree, the Z axis is adjustable and fastened using M3x12 screw.</p>

I bought some lenses from Amazon and wanted to get a better angle for my OctoPrint timelapses. This added the M3 bolt holder from the camera back of one design and added to another design. ... ## Things you need to print: * camera_back.stl from my...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...