raspberry pi model b rev 1

This model stand features a sturdy metal construction with a flat top and a set of detachable risers. You can place any type of electronics or device on the surface, from speakers to power supplies. With four height adjustment levels, you can...

Each aspect of the customizable model can be altered and refined using this intuitive interface, giving designers unmatched control over the finished product. Adjustments can be made across a range of parameters, all aimed at perfecting your end...

There already is an abundance of raspberry pi cases on Thingiverse, but I went ahead and created one anyway because I felt like it and had a blast doing it. I aimed to achieve several key features in my design: * Easy to print without support, with...

This is my Raspberry Pi 4 compact and modular design that should print pretty fast. You can use M3 screws to fix the board to the base and the cap but you can also use it without screws. It should click and stay so. You can lay it down or place it...

Designed to securely hold the Raspberry Pi along with the standard mount of the HifiBerry DAC+, this enclosure also includes additional space on the bottom for factory nylon screws, and slightly higher holes on the back to accommodate the added...

I liked [@karelv's case mount](https://www.prusaprinters.org/prints/29139-prusa-i3-mk3s-raspberry-pi4b-case-profile-mount-fo) but a) it doesn't work for a Raspi 3 B+ and b) I wanted the USB cable to go out toward the back. So I took its rail mount...

This is my Raspberry Pi 4 with a sleek and compact modular design that's perfect for fast printing. You can securely attach the board to the base using M3 screws or go without them altogether - it should click into place and stay firmly in position....

I liked @karelv's case mount but a) it doesn't work for a Raspi 3 B+ and b) I wanted the USB cable to go out toward the back. So I took its rail mount system and attached it to <a href="https://www.thingiverse.com/thing:3719217">@Malolo's base</a>,...

This is a remix of R31L4ND's Raspberry Pi 4 Case which can be found here: https://www.thingiverse.com/thing:4004856. I modified this to allow a 40x40x7mm cooling fan and this required me to modify the case by adding 4mm of height for clearance to the...

Remixed version (https://www.thingiverse.com/thing:3719217) to use with the Pi TV HAT and 30mm Fan

... 3mm acrylic material. Required hardware includes six M3-12 screws and ten nuts, with four reserved for use as standoffs under the PCB. The PI holes are slightly smaller than 3mm, necessitating a slight expansion to accommodate standard fasteners.

... Esquilos for making this project so easy; they're a lifesaver! You can find more details on Thingiverse: http://www.thingiverse.com/thing:1637227 Printer Settings: Printer: Geeetech Prusa I3 Pro B Rafts: No Supports: No Resolution: 0.2 Infill: 80%

Two variations are included: 40mm and 30mm - the lid can be better secured with screws if you are using 16mm M2.5 hex standoffs to secure the Pi to the TFT (but longer screws than the included ones are needed, around 5mm) - include slots to allow...

The original model of the bottom part of the case had 4 pegs that were too wide for my RPi 3B+, so I narrowed them to fit. ... Tinkercad source: https://www.tinkercad.com/things/9PZf6M7RzSg-rpi-3-bottom-case-part

His original model was truly impressive, but I found the locking pole to be quite weak when made with ABS. To address this issue, I created a new design that incorporates a screw-in mechanism. To assemble this model, you will need an M1.7 or M2 screw...

These are based on the Thingiverse model here: https://www.thingiverse.com/thing:3640994 I just added holes of the correct diameter in the correct locations. Print instructionsI printed this out of Prusament Galaxy Black PLA on an MK3S with a 0.6 mm...

A Handy Mount Designed by Kilroy01. This mount was quickly put together using clip. ...The holes are designed so that M2.5 bolts can be threaded straight in, and they also have open backs for use with a slim nut on the back side if desired.

・countersunk screw M2.6 15mm x4 ・Nut M2.6 x4

Enclosure

To assemble this DIY project, you'll need to gather a M2.4 to M2.7 × 10^13 mm screw with a countersunk head, typically used for wood screws. Additionally, consider adding a GPIO cover and VESA mount options, which come in two sizes: 75mm*75mm or...

I'm not sure what you're referring to. ...Could you please provide more context?

This is my very first attempt at creating a 3D printed design.

A quick mount made using the clip kilroy01 has designed. The holes are designed to have M2.5 bolts threaded straight into them, there open back as well so you can use a slim nut on the back side if wanted. ... Any suggestions leave a comment i might...

Printing has not begun. Added extra gaps to aid heat dissipation effectively now. ...Modified design influenced by project on www.thingiverse.com with identification 396858.

・countersunk screw M2.6 15mm x4 ・Nut M2.6 x4

Remastered to simplify page layout, I've divided the content into distinct sections for effortless printing.

Here's the deal - I'm rocking an Arduino camera that's basically the best working prototype yet! ...If you've got some sweet ideas for improvements, be sure to leave a comment and let me know.

Unfortunately, it didn't fit my Pi Cam Rev 1.3, which I still had lying around, because the image sensor was slightly bigger than the cutout and the small ribbon cable was a bit shorter on my version, causing the image sensor to be offset from the...

A 3D printable Raspberry Pi case inspired by the Playstation 1, a stylish case to use in conjunction with RetroPie emulators.Raspberry Pi 3B reference model created by Mechatronics ArtRaspberry Pi 3 Model B Reference Design Solidworks CAD...

COMPATIBLE WITH THE FOLLOWING DEVICES: • Raspberry Pi 1 • Raspberry Pi 2 • Raspberry Pi 3 PRINTER SETTINGS ARE AS FOLLOWS: • Extrusion Width: 0.40 mm • Layer Height: 0.20 mm • Top/Button Layers: 4 • Outline Perimeter: 2 • Infill Percentage: 20% •...