raspberry pi rack mount thingiverse 3d models

The angled versions make sure the camera mount is parallel to the bed.If you have for example an intake duct on your fan - as seen on the pictures - , you will need the 'long' versions, if not; you can use the shorter versions. The Pi camera I use is...

Meshed together two different Camera Mounts that were already on Thingiverse to create a Ender 3 S1 mount that works with my Octoprint camera. ... Update: Added version 1.1 that makes the camera mount slide on the the printer arm much tighter and fits...

# DIY Peephole Camera Mount for the Raspberry Pi 4 ## Important Details to Note The peephole in the pictured example is approximately 12 millimeters in diameter. This design is specifically tailored for use with MSLA printers. The threading on this...

This is a clamp mount I designed for my Flashforge Dreamer so I can stream my 3D Prints on MyMiniFactory TV. It lets me adjust the camera height and clamps to almost anything the feet can fit onto - about 6mm or less. Print Settings: Printer:...

The head has 3 M5 holes in the base to attach the mount, along with 4 M2 holes inside the head to mount the camera to. The teeth partially occlude the camera vision, but not badly. The extent of this is shown in the gallery. Instructions LEDs are...

... GoPiGo karts. This design is an adaptation of the ball head mount found at https://www.thingiverse.com/thing:2737276, with credits going to Bravehartk2. ... Required Components: - Round magnets measuring 3mm x 1mm - M3 bolts and nuts - Superglue

... ...Wanted this so I could add it to my printer and without to unsued mounting flanges. Also made a opening for the GPIO headers. Source files are in SketchUp file format. ... Original can be found here: http://www.thingiverse.com/thing:29263

Designers can enhance the camera housing found at Thingiverse under 1707484 by incorporating a sturdy bracket mount. ...Despite this addition, users will require obtaining the lid piece directly from the original model.

A 'nifty betitled adapter to fit a 'Zero into a classical mounting space, board, and / or bench-case. ... If you would prefer it to lay flat: https://www.thingiverse.com/thing:4872620 Cheers! ... -Rn

Read the readme.txt file carefully - it's packed with helpful info about setting up your new camera, complete with flash and hot shoe mount features! ...Check out the inspiration behind this project at https://www.thingiverse.com/thing:685074.

Three M5 holes at the base facilitate attaching a mount, while four M2 holes inside enable camera placement. The teeth may obscure some of the camera's view, but this limitation isn't significant as evident from the accompanying gallery images. LEDs...

I needed a means of mounting my pi camera inside of my printer enclosure. I don't like any of the printer-mounted camera case options and couldn't find anything else that fit my needs. Decided this would be a great learning project for Fusion, so...

This contains the redesigned file from thing:899284\r\nCrew mount holes are too big, originally 6mm in diameter.\r\nRedesigned the component and reduced hole diameters.\r\nSmall holes now have a diameter of 2.5mm.\r\nCooler mountscrew holes are now...

This part adapts the Pimoroni Pi Camera mount sold by Adafruit http://www.adafruit.com/products/1434, to fit Pan-Tilt Kits like these: http://www.adafruit.com/products/1967, http://www.adafruit.com/products/1968. Instructions: 3D printing makes this...

This model allows you to mount your Pi Camera Module 3 to any vertical 2020 aluminum extrusion. I designed it to mount on the side of a Voron 2.4, but it should work on other 3D printer designs too. Because of the angle, it's a particular great way...

Printed out the beautiful case design from dktosoch: https://www.thingiverse.com/thing:2844013 But it has no way of mounting. All other remixes are fixed, so I made this easily detachable mount with a design that would fit the case. The mount has 0.1...

The new design perfectly complements the original Pi for first-time users, ensuring a seamless and intuitive experience from the very start.

Remix is designed to accommodate a broad field of view using the high-resolution, wide-angle capabilities of the Pi Camera.

I'm featuring a remix from yazgazan over at Thingiverse: https://www.thingiverse.com/thing:2085090\r\n\r\nI tweaked the mount part, allowing it to securely fasten onto my electricity distribution box with ease. ...The gap between holes is now precisely...

Here is the original text rewritten in American English: I remixed the Sainsmart Camera Mount from Thingiverse at https://www.thingiverse.com/thing:239268. I modified the base to be a flat surface, allowing it to be securely attached to a wall using...

Allows you to use the "Articulating Raspberry Pi Camera Mount for Prusa MK3 and MK2"( https://www.prusaprinters.org/prints/3407-articulating-raspberry-pi-camera-mount-for-prusa-m ) by Sneaks with the Waveshare Raspberry Pi Camera (I) (...

This project includes a modified VESA mount for attachment to a printer, featuring only half of the original mount to avoid unused flanges. The design also has an opening for GPIO headers. SketchUp files are available for download, and the original...

This camera mount is based on several others I found here on Thingiverse. My aim was to improve positioning, stability, and assembly. Note: After using this for a time, I can say you will need to attach this using some tape or other temporary...

This is a remix of https://www.thingiverse.com/thing:4921670 to make the mounts fit on the side of an Ikea LACK table. I also designed two spacers to give ample clearance for the GPIO extender. On the original model I could never get the print in...

I printed out the sleek design from dktosoch:\r\nhttps://www.thingiverse.com/thing:2844013\r\n\r\nHowever, it lacked a way to mount it securely. All other remixes had fixed designs, so I created this easily detachable mount with a design that...

This results in an improved time lapse by focusing on the growth of the print without any distraction from its changing position.\r\n\r\nThis particular camera mount was inspired by several other designs I came across on Thingiverse. ...My objective was...

I'm a big fan of @Tommyelk's camera mount that cleverly utilizes the aluminum extrusion rail on this thing: https://www.thingiverse.com/thing:2540674 - it's really smart! And then there's the RPi camera holder in this mount re-mix by @c_wolsey, which...

... to the backplate to accommodate cabling needs. ...Unfortunately, my USB and HDMI cables barely fit, but that's not a big deal. Thanks again to KronBjorn for creating such an incredible open-source rack design! ...I'm really impressed with his work.

I downloaded https://www.thingiverse.com/thing:3243466 but it looked weird sitting under my TV, so I decided to attach it to the VESA bolt holes on the back of the TV.\r\n\r\nI uploaded the STL into TinkerCAD, and added a mount for the m6 bolt, and...

This is a remix of https://www.thingiverse.com/thing:3735600/files It is designed to mount to a 2020 extrusion rail. It used 2 m3 screws with 2 m3 t-slot nuts. ... It will work with any of the tops provided by the og post.