raspberry pi rack mount thingiverse 3d models

(Work in progress!!!) Current version is too tight for original Pi b+ I was hooked by OctoPi, and it's not without mixed feelings that I decided to use it, but the benefits clearly outweigh the negatives. After using it for a week, I decided to...

This mounts a Waveshare 4.3 inch DSI LCD with a Raspberry Pi3B+ inside an Ender 5S1 in the original screen mount location. It's quite likely to also work with a Pi4, but I haven't checked. Once Klipper is installed on this printer, the old...

Modification made to bottom Case from the original files at https://www.thingiverse.com/thing:3220196 Preparing Case for attachment of Raspberry to printer. Top case file is the unmodified original file from https://www.thingiverse.com/thing:3220196...

Here's a quick recap of the updated design: I swapped out the VESA mount for magnets and beefed up the holes at the base to fit M3 inserts. ...This modification is part of my upgrade plans for the JGAurora z-603s, where my OctoPrint/PI server will be...

Back Plate to mount pi zero w to the wall. The cut-out is for clearance on some hammer gpio pins I used. ...The screw holes are 2.6 mm in Fusion 360 but 0.3mm of it is for tolerance

I added a rail mount that allows me to securely attach my Pi to any of the convenient rail ends on my Ender 3 Pro printer. ...To bring this project to life, I used a 0.6 millimeter nozzle size, printing at a moderate speed of 125 millimeters per minute...

... basic rework of Dvogonen's Pi Camera holder, I included an arm and a 2020 V-Slot base. ...The arm was designed to enable adding multiple units to lengthen the mount at will. ...I also added an M3 T-Nut file - you'll need a couple of those in addition.

... the face plate of this to fit my Pi Cam No IR V2. ...Made the hole a little bigger to give some extra clearance, and lengthened the stand offs to make it easier to mount. ...You'll want to flip it over in your slicer unless you want to iron the face.

I replaced the PS Eye mount with a modular one, combining it seamlessly to fit the new Pi Cam's auto focus feature. I printed out a base plate and matching mount, then proceeded to print additional arms as required. The attachment process involves...

To assemble everything, use the knurled knob from http://www.thingiverse.com/thing:631919 and combine it with the camera mount and ball joint found at http://www.thingiverse.com/thing:247590. The initial bed mount was a modified version of...

I use Octoprint but my Raspberry was a total disaster with cables and after an accidental unplugging I decided to create a mount to get it out of the way. This is what I came up with. I used 2 X3/8 inch screws to mount to the top of the left Z...

Work in Progress: a modular 1U Rack for Raspberry Pi 4B: Two outer frames for connection of 3x M3 threaded rods -a base for the Raspberry (with holes to power the RPi via pogo-pins from the button -two different tops for the base, both with mounts...

... on tinkercad... https://www.tinkercad.com/things/lQRLf5sSwrb The fan hat for the raspberry is at: https://www.amazon.com/gp/product/B07Y9LFP1J/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1 V2 version is now available for both the PI3 and PI4

My shot at a camera arm for the raspberry pi camera module v2 on the mk3 / mk3s. It's a modular system, that allows you to make the camera arm as long as you want. For hardware, you should only need some of the spare parts that came with the...

I was searching for a spot to attach the raspberry and came up with this solution that keeps it out of the way yet easily detachable. I used a pre-made mount for the ZeroW (can't recall where I found it) and designed a base around it which fits...

Redesigned for optimal performance on the platform, this model boasts a new design that eliminates the need for raspberry mounting pegs and required supports found in its predecessor. The frame has been reinforced with added thickness and rounded...

You need to use wither self tapping M2x10mm scres to mount or only M2X10mmscrews for mounting. Also, need to tap the hole with 1/4th thread tap in case you need to mount on tripod. The tolerences are well matched that even if you don't put screws,...

A case for a Raspberry Pi Pico (W) to allow it to both be attached to a wall and have a Pack attached. In my case, a Pimoroni Pico Enviro+ Pack.The case does not close off the gap between the Pico and the Pack to avoid temperature build-up affecting...

This is a custom rack enclosure for a Raspberry Pi paired with a HifiBerry DAC+ that fits perfectly into KronBjorn's outstanding 6" Rack Enclosure. Designed to securely hold the Raspberry Pi along with the standard mount of the HifiBerry DAC+, this...

After looking at all the pi camera mounts out there, I wanted to design one based on a ball-socket mount for better positioning.  This needs to be printed at .1mm layers or better to get the fine pitched threads to be clean on the tightening nut and...

... put on the front side. But it was too high so that the mounting screw was not reachable any more.I moved the case a bit. The cover fits from the original model.You need some supports (snug) for the ventilator opening.You can find the fan cover here

... Has a nice fit and you can easily slide your Pi in and out after installing it to your wall. I printed the version with the cutouts but I've added another one without them for easier printing without supports. ...Print in standard model orientation

I was looking for a sleek way to house my pi and hard drive setup for Plex, so I turned to Bigjeffrey's case design as inspiration. I decided to add a custom-made hard drive enclosure along with a sturdy wall mount. ... My hard drive of choice is a 4TB...

Visit my blog: https://3dchanh.com/   Designed a Pi camera to go on the x-axis so that your prints are viewable at any height. Print at 100% infill. V1 - Clears my custom parts blower, if you are stock, print V3 if you want it shorter. V2 - Cover...

Remix of https://www.thingiverse.com/thing:922740 with VESA mount removed as I liked the compact design, but did not need to mount it.

I designed a custom mount to hold all these components in one place, rather than searching for individual mounts. The two screws that secure the motherboard are likely to fit into existing holes, so I started by drilling a hole in the top right...

Such as .16 or .12mm. It just just not possible, in my opinion, with my design skill level, to make a snap type enclosure as the original Raspberry Pi designed parts were. The snaps are too small, are too delicate with printed, to provide a...

This is to make the camera mount compatible with the following X Ends: https://www.thingiverse.com/thing:3559732/files

Includes an 8 port RJ45 patch panel, switch panel, and a raspberry pi (~3) panel. Most dimensions were based on a standardized server rack, with the exception of the width (to accommodate the size of the switch). I included the step file so you can...

Just modified for a GoPro mount usage.Sources :https://www.thingiverse.com/thing:1950391https://www.thingiverse.com/thing:2994679 Print SettingsPrinter Brand:CrealityPrinter: Ender 3 Category: Electronics