raspberry pi rack mount 3d models

I'd like to merge the Raspberry Pi rack mount enclosure with a straightforward setup so I can utilize both the USB-C charging port and the mini HDMI connector.

2U mounting case for 12 Raspberry Pi's, 24 SSDs, or a combination of both. Updates: v1: Initial design. After printing, I realized the frames and ears don't sit flush all the time. v2: Updated the interlock mechanism so that the frames will...

Combined the cover plate and Pi 4 mount using a unique adhesive solution. ...The parts can be found here: https://www.thingiverse.com/thing:3022136 I secured them together with JB Weld's PlasticWeld, but if I were to reprint these components, I would...

remix

All models are the same as the original this thing was remixed from except that they offer a mounting option at 83.3mm as well as 96.8mm.

This works well with my rack mount remix with the sides removed allowing extra space to the left and right of the Pi. Print SettingsSupports: Doesn't MatterResolution: 0.2Infill: 25Note: If bridging is not an issue, it can be printed upright or...

I found ButlertheButler's mount for the pi https://www.thingiverse.com/thing:4167265 and he had a link to the Procraft Decora rack mount. I picked one up and his prints were perfect for it. I like to run my pi boards from a SATA SSD, so I designed...

... GPIO pins, I used a breakout board cut into thirds that allows me to solder jumpers without interfering with the hat itself. This works well with my rack mount remake with the sides removed, allowing extra space to the left and right of the Pi.

Remix of a remix: this case stands out with its enhanced height and covers the entire port area, allowing a CPU cooler to fit comfortably. Moreover, it's even easier to print, requiring no supports whatsoever. The lid is cleverly designed with a...

The printed elements are designed to perfectly fit the openings in the frame and provide a clever 4 slot Raspberry Pi 19" rack mount. The locks use a simple push/pull lock mechanism (snap-in rivet). If you want to save some money, you can just...

Rack Mount Design Ensures Perfect Fit for Raspberry Pi 4 and Optional POE Hat. M2.5x5 Screws Secure the Top of the Rack Mount in Place. Pre-Drilled Holes Allow for Easy Installation with M2.5x8 Screws from Below, Securing the Unit to Posts Above...

Configurable 2U rack mount for raspberry pi and arris modem with keystone jack to access the ethernet on the back of the modem. Can easily be modified to different rack widths. Assemble with threaded rod smaller than 5mm diameter. Let me know if you...

This sleek 5mm acrylic laser-cut enclosure enables secure housing of up to five Raspberry Pi devices within a compact 19-inch rack configuration.

Configurable 2U rack mount for raspberry pi and arris modem with keystone jack to access the ethernet on the back of the modem. Can easily be modified to different rack widths. Assemble with threaded rod smaller than 5mm diameter. Let me know if you...

Configurable 2U rack mount for Raspberry Pi and Arris modem with keystone jack to access the ethernet on the back of the modem. Can easily be modified to different rack widths. Let me know if you would like any other mounts for modems, etc! Includes...

This is an adaptation of a 2U bracket that I previously developed: * [Raspberry Pi 4 2U Rack-Mount Bracket](https://www.thingiverse.com/thing:4078710) It shares the same tray design, enabling easy transfer of units between these two mounts. This...

Raspberry Pi 4 Case for a Sleek Server Rack Installation, Complete with Room for Optional Accessories. The top features M2.5x5 screws that securely hold everything in place. Below the top, holes are precisely crafted for M2.5x8 screws to be inserted...

A versatile rack to mount the Raspberry Pi 4 in a standard 19-inch server rack. This design fits 12 RPi 4 units using Power Over Ethernet (PoE) in a compact 2U space for a neat cluster solution. I use the official PoE hat issued by the Raspberry Pi...

My two setups were: - 15-bay with single Raspberry Pi 4 8GB - 12-bay with dual Raspberry Pi 4 2GB For the 15-bay print: - (5) SATA 3-bay - (2) Double Back Tray Cover - (2) Double Back Tray - (2) Side Arm - (1) Single Back Tray Cover - (1) Single...

This orientation will prevent it from cracking when extrusions will be pressed in while assembling.Cut aluminium extrusions to the length specified and press them firmly to the corresponding mount holesVerify that assembly fits to your rack, remove...

Designed to accommodate up to four 2.5-inch by 7-millimeter solid-state drives, this innovative system was specifically crafted for RussRoss's Raspberry Pi rackmount setup. The SSD mounting mechanism is a sturdy three-bracket wide design. ...To enable...

Remix to fit orange pi 0

... so you'll need some padding or thick tape to align the ports with the hole. For more information about the project, including other materials used and how I assembled it, visit: https://harariprojects.com/2021/02/26/raspberry-pi-rack-mount/

Developing a Raspberry Pi B+, 2, or 3 rack mount solution is feasible by utilizing the "Raspberry Pi Sleeve" design available at YouMagine. ...This design serves as a basis for creating a customized case that can securely hold and organize your...

Needed a rack mountable Odroid-C2. ...Using Tinkercad, I cut out the side, so in theory, any Raspberry clone (like the Odroid-C2) that mounts will have clear access to the side. ...Front (Left?) rack ear without LED lights also attached.

... ear from the Raspberry Pi 4 2U rack-mount bracket by russross for 10 inches network cabinet. ... Caution: You need the rest files from russross - Raspberry Pi 4 2U rack-mount bracket project for completed printing! ...You find here only the longer ear!

The vertical mounting bracket is designed specifically for use with the model available on Thingiverse at https://www.thingiverse.com/thing:4125055. This bracket provides a straightforward installation process that doesn't require any support...

This is a mod for: Raspberry Pi 4 2U rack-mount Mark III for 14 Pi with 2.5" SSD https://www.thingiverse.com/thing:4756812 Originally this was designed for POI, but if you want to use it with power supply connectors, you can't place it on a shelf.

To save my rack size, I have created an enclosure, that fits two Raspberry PI computers next to 10” switch, replacing standard brackets/adapters. This one fits my TP-Link TL-SG1024D switch replacing original brackets and fitting it’s screws. Please...

... such an environment. This mounting solution caters specifically to users of that unique server casing referenced on Thingiverse with identifier #665042, allowing them to efficiently install their Raspberry Pi unit inside the given space constraints.