raspberry pi remote relay switch 3d models
118086 3d models found related to raspberry pi remote relay switch.thingiverse
This is a case to hold a 4 channel relay board. You can either print the 'tight' lid which is held on by friction, or the 'magnet' lid. For the magnets: You'll need 2 8mmX3mm hobby magnets. Glue one in the base and one in the lid. Of course, make...
prusaprinters
Raspberry Pi WaveShare Relay case with mounting feet. ... Using this as a case for my sprinkler controller</p>
thingiverse
I've got a Raspberry Pi server running OpenRemote2 which as well as IR over IP it also now has a 8-way relay board wired straight into a couple of remote controls for the projector screen and lounge table lamps. As you can see it requires a bit more...
thingiverse
This is a case for the 3 relay board for the raspberry pi to shield from the high voltage carrying pins.
thingiverse
Housing and clip to attach a [relay board](https://smile.amazon.com/gp/product/B0151F3A9Q/) to my [Raspberry Pi Sleeve Case](https://www.thingiverse.com/thing:2342050). ...The board is mounted with 2 M3 screws.
thingiverse
Files use to mount a rpi3 with a relay switch to a monitor
thingiverse
Simple Case for Raspberry Pi 3 + 1ch. ...Relay Card Notes for Hardware (Thanks 0110-M-P) RPi to bottom: Four #4 x 1/4" sheet metal screws Alternative #1: M3 x 6mm (will be an extremely tight fit and is not recommended) Alternative #2: M2 x 6mm w/ heat...
thingiverse
Includes an integrated switch lever, a section for a piezoelectric buzzer, and mounts for metal switch contacts and a circuit board with an LED to indicate power status of the Pi. A switch consisting of the lever, mounts for contacts, and metal...
thingiverse
I designed this for my new lack enclosure. ...It holds a standard 1/4 switch for lights and a Pi on/off switch that is secured by two tie mounts on the back side.
thingiverse
Raspberry pi case with dual relay board, also designed to screw into cr-10 control box.
thingiverse
Battery, Raspberry Pi, Relay Module (BPR) Mount onto preexisting plate for school project.
thingiverse
Other Parts needed: Raspberry Pi Zero with components needed to function (SD card, power supply, etc) Relay Board: https://www.amazon.com/gp/product/B01D4VFS6M USB Ethernet Adaptor: https://www.amazon.com/gp/product/B01AT4C3KQ Power Cord:...
thingiverse
This tray holds a Raspberry Pi (I used a 3B+) and an 8-channel relay board side-by-side. ...Perfect for bench testing.
thingiverse
Revised version of Parametric PCB mount box by nicholasclewis. ...Remixed to fit 4 relay shield for Arduino and Raspberry Pi. ... Prints easily with no supports.
youmagine
Simple relay box, using a Raspberry Pi and an 8-channel optically detached relay. Could be used for 230V or 110V systems. This version is build with 8 Schuko sockets, as these are standard for European mainland. The frames are screwed into the...
thingiverse
This is a Raspberry Pi and relay enclosure for a Zaribo 3030 extrusion frame. It also has a space for a Noctua fan with an on/off switch. There is a slot in the left side to run a Raspberry Pi camera ribbon cable inside the case. This should...
thingiverse
Relay Mount for Raspberry Pi 7" Touchscreen It's a pretty specific use case. It will accept two different relays: 12V 4ch Relay - https://www.amazon.com/dp/B00LW2GM84/ 12V Timer Delay Relay - https://www.ebay.com/itm/122552064797 Used for my OpenAuto...
thingiverse
This is a modified part of a 2 relay module for a direct attachment to raspberry pi You may need x4 M3 screws No bolts needed The clip was not needed neither, but it is attached
thingiverse
Raspberry PI 4 OUTDOOR CASE - bottom case: 1 Raspberry Pi 3B+/4B, 4 relay modules, 1 GPIO Expansion Board - top case1: clasic top case - top case2: 1 hole for wires, 1 camera clamp - 2 types of arm: 69mm and 109mm - camera holder tinkercad the box:...
thingiverse
This is a simple relay mount and cover for a Raspberry Pi, Arduino or whatever. I used foam tape to attach it to the power supply on my Ender 3 and Velcro to hold the cover on in place if I need to get to the relay. Ventilated to prevent heat...
thingiverse
I wanted a case to keep my Raspberry Pi 3B+ and Relay board covered while also having a camera and temperature sensor to monitor/control my Garage using Homekit.I'm running HAP-NodeJS to run everything on the Pi. I used <a...
thingiverse
This is a combined case for an OctoPrint controller which includes mounting of the Raspberry Pi 3B and a single 26mm x 50mm (20.5mm x 44.5mm holes) 120/240v 10A relay. Relay:...
thingiverse
Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: .2mm Infill: 30% Notes: I use this relay module to turn on/off the power to my printer and LED lights from OctoPrint, running on a...
thingiverse
Enclosure for a raspberry pi 3b+ and an 8 channel relay board with room for wiring and cutout for camera ribbon cable. Designed so I could use the Enclosure Plugin with Octoprint and have everything neatly inside the case. ... Zip ties were meant to...
thingiverse
## Description This *thing* was designed to fit a Raspberry Pi 3 B, a 4 channel solid state relay board, an Arduino Nano (with removed headers) and be mounted under a desk; it could also be mounted on a wall. the Raspberry Pi runs Pi-Hole and Node...
prusaprinters
This tray holds a Raspberry Pi (I used a 3B+) and an 8-channel relay board side-by-side. ...Perfect for bench testing.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p><p class="detail-setting printer"><strong>Printer:...