raspberry pi touch screen 3d models
99007 3d models found related to raspberry pi touch screen.thingiverse
This is a remix of the Raspberry Pi Offical Touchscreen stand by Stevezuki, I liked and used his for ages but then decided I wanted to hang my raspberry pi touch screen from a shelf. ... Quick remix of his file so it hangs with a 90 degree angle from...
thingiverse
I could not find an enclosure for the BTT_PITFT50 (BigTreeTech's Raspberry Pi 5" touch screen, so I modeled my own. It's a similar profile to the Prusa i3 screen enclosure. Requires 4 M3x6 bolts and washers to hold the screen in place. ... There are...
prusaprinters
I could not find an enclosure for the BTT_PITFT50 (BigTreeTech's Raspberry Pi 5" touch screen, so I modeled my own. ...It's a similar profile to the Prusa i3 screen enclosure. Requires 4 M3x6 bolts and washers to hold the screen in place. There are...
prusaprinters
you might have to push the case up against the right side to plug in your HDMI cable.source file are included. Here is the Link to the screen I used when designing this: Amazon.com: Raspberry Pi Touchscreen Monitor, Upgraded 7'' IPS 1024X600...
thingiverse
Raspberry Pi touchscreen case to protect the LCD panel electronics. Made to fit this screen http://bit.ly/RPItouchTindie Two sets of files; one set for large print area printer and one set for smaller print beds. There are holes for zip ties in the...
thingiverse
This is a remix of the Raspberry Pi 7 inch touchscreen stand. Looked great, but when I printed it, I couldn't get my screwdriver through the support to tighten the bottom screw. This version is about 3mm wider to accommodate the larger hole that...
cgtrader
This is a generic raspberry pi touch screen shield. This would work great for prototypes, allowing you to add the model to an assembly to make sure that all parts will "fit in the box". ...
thingiverse
This is precise solidworks model of lcd display below.
grabcad
This is precise solidworks model of lcd display...
thingiverse
This is a mount that I made to attach to the top rail of the shelf, to hold the 7" Raspberry Pi Touch Screen, and RPI. I use this for the touch-screen of my printer. ... ...
thingiverse
This is one for the Raspberry Pi Touch Screen, and may not work with the knockoffs. It might also work for the B+,2B,3B,3A+,3B+, but you may need to manually expand the ports. Due to the usb port on my screen, I had to add more than 8 mm of...
thingiverse
Requires a Raspberry Pi Model B+ and a 2.8" screen. ...Used in the MakerBot Factory.
thingiverse
This is an easy to print and install stand/mount for this [ https://tinyurl.com/s2l43n5 ] 7" touch screen. I'm using it with OctoPrint and TouchUI to control my Creatliy CR-10S. Very simple design only takes about 4-5 hours to print based on the...
cults3d
This is an easy to print and install stand/mount for this [ https://tinyurl.com/s2l43n5 ] 7" touch screen. I'm using it with OctoPrint and TouchUI to control my Creatliy CR-10S. Very simple design only takes about 4-5 hours to print based on the...
thingiverse
Decorative Bezel For Rpi 7 inch touch screen case: https://www.thingiverse.com/thing:1585924
thingiverse
3d .stl files for creating an enclosure for the official 7" touch screen for the Raspberry Pi. There is a separate file for for enclosing the RasPi B module.(or RasPi 2) It is attached with 4 slide on interlocking clips for easy removal for...
prusaprinters
I needed a case to house/protect the screen only.To fit in this case you can't use dupont connectors for the power, they stick out too far, I removed them and soldered my leads straight to the board, you may be able to bend the connector all the way...
thingiverse
This thing is a reference model of the Official Raspberry Pi 7" Touch Screen Display. The parts modeled in this thing are available here: Official Raspberry Pi 7" Touchscreen Display: http://amzn.to/28UEiWP Raspberry Pi 3 (Canakit with power supply):...
prusaprinters
This thing is a reference model of the Official Raspberry Pi 7" Touch Screen Display. The parts modeled in this thing are available here: Official Raspberry Pi 7" Touchscreen Display: http://amzn.to/28UEiWP Raspberry Pi 3 (Canakit with power...
thingiverse
Here are the components I used: Raspberry Pi 3 (CanaKit with power supply): http://amzn.to/293362J Official Raspberry Pi 7" Touch Screen: http://amzn.to/28UAYuL 32GB SanDisk Ultra Micro SD Card: http://amzn.to/28UB9WY Right-angle micro USB power...
thingiverse
Room for Heat Sinks. Lots of venting. Snap together. Tested Fit. No supports. 100% fill Any layer height. ...
thingiverse
This is a small clip that can be put into the top of the Raspberry 3 - Original touch-screen casing. I used it to mount my PIR (Passive-Infrared-Sensor = Movement Sensor) to the top as i wanted the screen to turn on automatically when someone came...
thingiverse
15deg angle brackets for Raspberry Pi Touchscreen. Mounted with M6 bolts and size 8 tnuts. Hardware: 6x M3x25 cylindrical head bolt 6x M3 nylon nuts 3x M3x10 cylindrical head bolt (min. 6mm, max 12mm length) Tap M3 holes, or screw directly...
thingiverse
Raspberry Pi 7inch HDMI Touch Screen Display-B 800x480 pixel USB Touch Rev3.0...
thingiverse
#Raspberry Pi 2&3 5" Touch Screen #Repetier Server Pro or OctoPrint (FREE!) Display case for a Raspberry Pi 3 model B (fit also for Pi2 Model B) 800x480 5" TFT display with XPT2046 touch screen which fits best to a BLV MGN Cube It can run Repetier...
cults3d
I printed this case for my Miuzei touch screen mounted on my raspberry pi 4. https://www.amazon.com/Miuzei-Raspberry-Full-Angle-Heatsinks-Raspbian/dp/B07XBVF1C9 https://www.thingiverse.com/thing:4663911 But I wanted a way to mount it to the Prusa...
thingiverse
I printed this case for my Miuzei touch screen mounted on my raspberry pi 4. https://www.amazon.com/Miuzei-Raspberry-Full-Angle-Heatsinks-Raspbian/dp/B07XBVF1C9 https://www.thingiverse.com/thing:4663911 But I wanted a way to mount it to the Prusa...
thingiverse
This console supports Raspberry Pi (2 or 3) and the official 7" touch screen display and housing. It is designed to use the display (housing) in an upside down orientation as shown on the pictures. I made this due to some troubles with the Raspberry...