raspberry pi zero w camera case 3d models

Very compact, 3D printed housing designed to work seamlessly with: • Raspberry Pi Zero • Raspberry Pi Zero Camera • Pico mounting bracket (2020 V-Slot version) • Pico mounting bracket This housing boasts ample internal space for a heat sink and...

I remixed the Slim Rpi0 case by tvarok on Thingiverse to also fit the non W model with or without the header soldered.I've also made additional base plates to accommodate the pins.It's mounted the same way as the original, that is with screws or...

I remixed the Slim Rpi0 case by tvarok to also fit the non W model with or without the header soldered. I've also made additional base plates to accommodate the pins. It's mounted the same way as the original, that is with screws or printed pins. ... ...

I couldn't find any case for RPi Zero 2 that I liked, so I decided to make my own from scratch. I took design inspiration from Sparkovsky's Acrylcase (https://www.thingiverse.com/thing:2190506). I made several versions, with vents, slot for a...

I couldn't find any case for RPi Zero 2 that I liked, so I decided to make my own from scratch. I took design inspiration from Sparkovsky's Acrylcase (https://www.thingiverse.com/thing:2190506). I made several versions, with vents, slot for a...

Case for the Raspberry Pi Zero (W model, other model works too) for using the 8086 Consultancy Solder-less Zero Dongle that can be found at https://www.8086.net/products v2 Update More space for ports LED hole Curved edges Closed down front around...

replacement bottom case for wall mounting

After printing Jugulaire's Pi and Breadboard Holder I realized that I had misplaced all of my half-sized breadboards. ...I spent a few seconds in Blender and remixed it to fit a full-sized breadboard.

After crafting Jugulaire's Pi and Breadboard Holder, I discovered that I had misplaced all of my standard-sized breadboards. ...I devoted several moments to Blender and repurposed the design to accommodate a full-sized breadboard.

A key adjustment to this project:\r\nhttps://www.thingiverse.com/thing:1998032\r\n- Remove the GPIO slot since my board lacks pins.\r\n- Adjusted standoff heights/radii for smoother board insertion *and removal*, and added new standoffs to the lid to...

This case is a remix of DonNetWorker's great case. ...It is designed to bolt right onto the side of the Monoprice Mini using the existing bolt holes.

This case is a remix of DonNetWorker's great case. ...It is designed to bolt right onto the side of the Monoprice Mini using the existing bolt holes.

Simple open air case, all you need is some standoffs and screws

Remix after slim case. ...Modified so it doesn't have GPIO opening if you don't need it.

This is a remix from https://www.thingiverse.com/thing:398515. ... I modified the case design to incorporate a male V-Slot addition. That way I can slide the case in the V-Slot rail on my printer. Let me know your feedback. ... Thanks!

This a screwless case for the 8086 solderless usb dongle that allows you to use your raspberry pi zero as a gadget. I've created a couple of lids for this, with and without space for the header. I've also blanked out the connectors, but you...

I required a housing that could be installed with minimal visible connectors, particularly I just wanted the power connector accessible.\r\nThis design builds on the elegant casing from SnowmansEye, and seals off numerous ports to fit my...

I liked the case but I wanted to customize it a bit so I made it shorter, removed that giant square cutout for the power, changed the design of the controller & Memory card slots, and added support for a magnetic locking system (6mmx3mm)...

This is a remix of the case developed by Frank Rennemann (https://www.tinkercad.com/things/jaONuzFfFCc), and was updated to accomodate the Raspiaudio+ Audio hat. It assumes using a 6mm stand off on the base. ...Two screw holes are at the bottom to...

This is a case for an unofficial Chinese Raspberry Pi camera that can be purchased on eBay. A similar, yet distinct camera uses the exact same sensor as the official Raspberry camera, but features a larger PCB board than its original counterpart,...

Made RPi case deeper, added two-section front for the LCD1602 module, added heated threaded inserts (M3 x 6 x 5)for mounting. I'm using the Waveshare 1602 (RGB, includes JST connector): ...

This project involves a Chinese Raspberry Pi camera available on eBay, which offers unique features over the official camera. Using the same sensor as the official camera, the Chinese camera boasts a larger PCB board that demands an alternative...

... This mount also works for a raspberry pi zero w/ zero however octoprint doesn't seem to run well on those so your mileage may vary. ...The tops for this case can be downloaded from the original poster as I didn't want to just repost them here.

Raspberry Pi Zero 2 W with 40 pin male connectorCombined Raspberry Pi Zero 2 W from Hasanain Shuja and 40 pin male header from Ahmed AbdelftahThanks for your work!

Raspberry PI Zero W holder for original Prusa i3 mk2, perfect to OctoPi and to create smooth time lapse.

Case for the Raspberry Pi Zero (W model, other model works too) for using the 8086 Consultancy Solder-less Zero Dongle that can be found at https://www.8086.net/products v2 Update More space for ports LED hole Curved edges Closed down front around...

......I have the newer Pi Zero 2 W, which is more powerful, so it comes with more heat. It might have been fine, but I just added a few additional vent holes for extra air flow to the higher temp hardware. ...Check the original thing for the case portion.

You will need: 1 x Raspberry Pi Zero (I used v1.3 Pi Zero W) 1 x Pi Module camera (I designed this for the night vision version, but others may work) 1 x Camera cable adapter (If your not using the Pi Camera V2) 8 x M3 Nuts 8 x Counter Sunk M3...

A snap fit housing for the Raspberry V1.3, V2.1 and V3 cameras.2018-10-09:Made minor changes so that the v2.1 camera fits better.2023-12-25:Enlarged hole in the housing for the V3 camera module.Added a housing with 90° rotated camera...

This project is for a custom-made enclosure specifically designed for the unofficial Chinese Raspberry Pi camera, which can be purchased on online marketplaces like eBay. Noting that this camera utilizes the identical sensor as its official...