rc camera mount 3d models
446783 3d models found related to rc camera mount.
thingiverse
Mount for small camera on Evader model RC car. Mount is secured to RC car chassis by nylon zips. A pan head stove bolt is threaded into camera shoe inset, with the pan head of the bolt in turn clamped upright by the threaded cap screwed onto the...
thingiverse
Mount to hold GoPro/any camera onto most RC frames. Instructions Printed with ABS at 10%infill. No supports needed. ...I recommend heating the nut to get it to fit tight.
thingiverse
RC Lunchbox camera mount, was sick of strapping coming loose, simply remove the 3 screws holding on the front bumper and add this 3d printed one, an easy print and ready to mount after printing
thingiverse
I've remixed this for use with my cell phone camera mount. If you found this useful, please donate what you think it is worth to my paypal.me. Help cover the time of design. Thanks, Enjoy! ...
thingiverse
This is a camera mount/bracket for the FU-RC Kore frame. ***DISCLAIMER*** I have not printed and checked the fit. ...So if you use this please let me know how it fit or make and post the correction thanks.
thingiverse
Improved radius for strength Moved the mounting point lower to follow the curve of the dome through all the angle range Thicker frame, should not break anymore (use longer 2mm screws to mount the camera). ... Print in ABS or PETG for best results, no...
thingiverse
It is a DVR and and FPV camera in one unit and the quad mounts for those cameras were too small. With this you can put a seperate battery behind the camera and secure it and the camera with rubber bands. Next I am going to try and have a cage over...
thingiverse
This is a casing with angle adjustable camera mount. ...designed to clip in a "FatShark 5,8Ghz 250mW RC VISION" Transmitter. And the camera mount for FatShark TVL600/700 FPV Cam. ... you need a screw M4x20 and a Nut M4
thingiverse
It can be used if the camera mount is broken due to a collision or malfunction. The distance of the hole is slightly different from the genuine. Since I'm a newbie pilot, I broke it up a lot. i'm used Caddx Turtle v1 camera. ... The size of the...
thingiverse
Akaso v50x iFlight XL and Sabotage RC Dingo camera mount. Both mounting styles come in a 15° and a 30° mount. Note: This is experimental as I do NOT own any of the equipment listed and measurements may not be correct. ... If you print this and it...
thingiverse
This camera mount is intended to be used with the Martian II/Impulse RC Alient quadcopter frames. The camera mount has been designed to be mounted on the top carbon fiber plate, using the M3 screws included with the frame. This camera mount is also...
thingiverse
... you select is important. The front camera mount & tail camera mount fits the RunCam Micro Swift camera or any camera with a width of 19mm. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/kWr6G7L6w8P
thingiverse
A generic flat mount for adding stuff to your Tamiya TT-01R Type E car. Just tight enough to snap on very securely without using adhesives - you can easily pick the car up with this. Very strong, too. It'll also fit a netbook. This is more for use...
thingiverse
I took the excellent design from Pilotboy, made the holes smaller, added standoffs to the back so that a board cam can be screwed on directly from the back without the need for additional nuts or spacers and adjusted the size and mounting tabs for...
thingiverse
... with camera and transmitter, this solution is for you. ...You can easly mount mini camera with transmiter on the hood or on the roof of your RC car. The design is simple, just to test if this kind of fun is satisfying. ...There are 2 hights of mount.
thingiverse
This is a camera mount for this type of camera. It's made to mount on this platform. Which is made to mount on the RC Tank by Staind. This would probably be pretty easy to remake for other uses. I printed this with PLA. Print the base with...
grabcad
Personally designed & built pan-tilt camera mount for FPV flights
thingiverse
An adjustable angled camera mount to hold the common HS1177 FPV camera onto the DL180 Quadcopter frame. Requires no holes or screws to hold in place. Uses the standard HS1177 Screws to hold the camera. ...Print Settings Printer: ...
prusaprinters
An adjustable angled camera mount to hold the common HS1177 FPV camera onto the DL180 Quadcopter frame. Requires no holes or screws to hold in place. Uses the standard HS1177 Screws to hold the camera. Print instructionsCategory: R/C Vehicles Summary...
thingiverse
Designed with Fusion 360! ...Printed in PLA and fits perfekt! Only one hole design so Camera angle freely adjustable!
cults3d
rail mount camera for ALIEN 5 IMPULSE RC. ...You can adapt all types of camera:support for mobius(here), Support for GoPro (found in lethal conception SR 5 download site) etc...
thingiverse
rail mount camera for ALIEN 5 IMPULSE RC. ...You can adapt all types of camera:support for mobius(here), Support for GoPro (found in lethal conception SR 5 download site) etc...
thingiverse
Pan-tilt camera mount for RC crawler. -------------------------------------------------- The mount has a column design: tall and skinny. The column is supported by a ball bearing, to reduce vibration and strain on the pan servo axle. The bearing...
thingiverse
3D printable camera mount for Tamiya DF-03Ra Celica RC car. Tested with Liquid Image Ego action camera. Should fit also for GoPro. Instructions I printed the mounting plate with Dimension SST1200es and it fit perfectly. When attaching the plate on...
cgtrader
Its a 3d printable mount for GoPro Cameras or normal Cameras.Its adjustable up to about 270°. Its Desinged to fit on a REELY Carbon Fighter Evo rc car but it can easyly be redesinged for almost any other rc car or simular. ... additional parts: 1x...
thingiverse
25° + 35° Camera Mount for the Impulse RC Alien 5" for runcam, mobius, Gopro Session, SJ cam M10 would be nice to see your makes;-) and get a like