rc camera mount 3d models

--- <h3> Remix from </h3> https://www.thingiverse.com/thing:3382756 --- I liked the holder, but the curves were a bit too rough for me. So I redrawn it for a higher resolution. I also suspected a predetermined breaking point on the slope...

I needed some illumination at the extruder, but didn't require the fan or ductwork. So I tossed it into Sketchup and customized it to be exactly what I wanted. ... I used this LED; https://alofthobbies.com/led-lights-5822.html?___SID=S Print Settings...

Attaches to the front of the hotend bracket. ... This component is clearly depicted in the 3D model of the RatRig V-Core, yet appears to be absent from the actual printed components, prompting its creation.

Customized version of https://www.thingiverse.com/thing:5816088 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5816088

I designed this adaptor for my ender 6 to add and Orbiter v1. This is designed for the orbiter with the v6 heatbreak used as a filament guide. It bolts to the holes meant for the factory strain relief. I added a strain relief spire with and hole...

Difference between original and remix is the removal of a small annoying bump on one of the sides that was affecting my OCD.

Bracket that holds switch up against the back of the TV. I used it on a Hisense TV. ...It may not work if your TV and bracket are closer or further apart than my set up.

Please utilize a Type-M5 screw for secure attachment.

Quad Beam pieces to homebrew experimental antenna. fits 1" pvc and 6mm fiberglass rods used for driveway markers that can be bought at the hardware stores. 5/16"-18 threaded holes for set screws. ...Use a tap afterwards to clean up the holes is a good...

I created this design specifically for the filament guide that's included with the all-in-one upgrade STL file. ...The original dovetail component had significant flaws, resulting in air pockets forming during prints near the extrusion tabs.

To successfully transport a nearly flawless stone to China's top-tier fake apex replica facility, you will need to follow these precise steps. First, carefully inspect the stone for any imperfections or blemishes that could compromise its...

People are split in two categories - those on the left side of the scale and those on the right side.

This clip-on accessory holder fastens securely onto the Dyson v7/v8 motorhead wand's shaft. The design is highly customizable, allowing users to choose how many accessories it will hold. However, to avoid overlapping holders, we recommend specifying...

<p>No more crowded desk space and dust protectors on the floor - just screw up your dell power brick to your desk/wall etc.</p> <p>Best for permanent bricks - if you carry your dock around more often, grab another.</p> <p>Fits for 180W Power...

Modified the original controller hook to slide right onto the front of NZXT's S340 PC case, should hold any Xbox/Playstation controller. ... I recommend making the entire hook skinnier/wider based on the controller you use, to make it harder for the...

Originaly desingned this for my own usage but now I'm charing it. ... Hope you like it tho.

I did a longer and angled version for my Fast helmet Rail. It works great with my Sony FDR X1000. ...It should work with other Sony Cams too.

Customized version of https://www.thingiverse.com/thing:5816088 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5816088

Customized version of https://www.thingiverse.com/thing:5816088 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5816088

I strengthened the support, noticing that the original part was yielding under stress and I knew it wouldn't hold up to heavy use.

Protection de bras et support de caméra (Gopro ou autre) pour les frames Culture FPV HighCult et LowCult (5", 6", et 7") Imprimé en TPU 95A Pour le support de caméra, un remplissage important (40/50 %) permet de renforcer le support en cas de...

<p>Easily add a fire alarm to your enclosure using the extra nuts and bolts included in the kit. </p><p>We've made multiple grates for the fire alarm, so choose whichever you prefer. </p><p>The link to the compatible fire alarm can be found...

Customized version of http://www.thingiverse.com/thing:526257 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=526257 Using the following settings: iPhoneDepth is set to 10.8 iPhoneWidth is fixed at...

Print with small LCD window towards the bed. ...I printed with supports and tree supports

Full print with 4x4x4 walls/top/bottom and 15% infil Glue in lettering and spade. ... Star may need minor sanding but should push fit into the space tightly and not need anything else to secure it.

The loudest component in the QiDi Tech 1 printer is its tiny 40mm x 10mm fan, situated inside allegedly cooling stepper motor driver modules. When you power up the printer, this fan dominates the sound scene whether printing or idle. ...After a year of...

This model requires no supports, has the SNES logo debossed on the front. ... You can use tape on the back, drill 2 holes or simply stand it up on a shelf

I needed to free up space on the workbench so I built this to hold my computer against the wall securely. It should work great with drywall anchors, which provide a solid hold. To ensure stability, I recommend using at least two anchors below and...