rc plane piper cub 3d models

Robotic guard.

The model was brought in by a customer who needed repairs, and since we weren't familiar with the original motor mount used in the Flyzone switch, we took a close look at its design to get an accurate replacement. ...Fortunately, our guesswork paid off,...

This is a custom housing for the Immersion VTX on my Volantex Ranger 1600 FPV aircraft. The base grips securely onto the fuselage, and I secured it using Loctite plastic bonder epoxy. The transmitter fits snugly inside; I leave it slightly loose for...

This upload showcases a complete 3D printable airplane model consisting of wing sections, fuselage, and tail parts. After printing, you only need to add remote control components, a brushless motor, speed controller, servos, and wiring. The SLDPRT...

Inspired by Large Valiant (hungar 9) Balse and plywood 2700 wingspan

To preserve the roundness of the wheels while the airplane is storaged for the winter.

This is a personalized design based on the model found at http://www.thingiverse.com/thing:24229. The Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=24229) was used to create this unique version. ...Key adjustments include a...

This human hasn't taken to the skies yet.

The tire has a 58mm or 2.25-inch diameter, made from a 12mm foam rubber obtained at "Clark Rubber." It's printed using ABS material and each wheel weighs approximately 12.8 grams.

Landing gear assemblies are crucial components of model aircraft, and for the Sonicmodell Binary 1200 mm, a high-quality landing gear is essential to ensure safe and stable landings. The binary design concept of this aircraft demands a landing gear...

Speed pane concept with 3 meter wingspan

I'm aiming to install nosewheel steering in my ultra-light aircraft, weighing around 680 grams. To accomplish this, I've engineered a system utilizing a 9-gram servo (Metal geared is highly recommended) and 2mm piano wire. ... ...

Newly uploaded files have been processed. No additional external support is required for the aileron, resulting in a 50% faster printing time. Further enhancements involve increasing pin sizes for added strength. The design includes three components:...

The documents I employed to construct my DH.88 Comet for the prestigious FliteTest Red Bull Air Race competition.

A personalized adaptation of the Thingiverse model (http://www.thingiverse.com/thing:24229) was created using the Customizer app with settings including axle clearance at 10, wall thickness at 5, a 36mm width, and a tolerance of 5. ...The nail...

<h1>Story</h1> <p>This long-overdue continuation of my airfoil study is a completed wing with full internal structural supports that will be lightened later. You'll notice there are no provisions made for flaps or ailerons, just functional...

Made this sturdy wheel hub to match the lightweight foam cut bush wheels I crafted for my SuperSTOL model, featuring an interior "wheel stop" design that turned out really well.The lightweight foam cut wheels I designed measure approximately 5.5...

Multi-axes Servo Wire Support

Based on my previous Battery Mount plate here: https://www.thingiverse.com/thing:4947126 While the old mount was meant to be used with Velcro straps or similar, this version is specifically designed to be used to mount Li-Ion Cell packs in a...

I designed this hook to store my E-flite Viper 70mm EDF jet. It is fairly large and should be compatible with a lot of different models. I load tested an ABS prototype printed at 10% infill to nearly 19lbs (8.6 kg) with minimal flex! Teh final...

Servo wires receive a vital assist from humans.

Be careful!!: 3D printed propellers could possibly explode when reaching high rpm's. I strongly discourage using it in BLDC motors, or any other high-rpm motor. I just modified the original code (many thanks to the og author, great coder too!) so...

This tool is specifically designed for creating precise indentations in the center of hinge parts, as demonstrated by the model at http://www.thingiverse.com/thing:31249.

Print SD card slot facing down. Surprisingly, this has little effect on flight handling even on a light foamie but I would advise fitting on right wing so that the drag is offset by the prop side-thrust. ... Fitted to the wing with Velcro, I couldn't...

Customized version of http://www.thingiverse.com/thing:24229 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=24229 Instructions Using the following options:...

Clever Locks with Push-Stop Mechanism

Servo-based mechanizm to make a foldable landing gearI'm always using this landing gear wheels in my projects because it's best price to strength, about 2,5-3$ and handle models up to 1 - 1,5 kghttps://s.click.aliexpress.com/e/_EvWNq3JAbout servos I...