rc plane pusher propeller 3d models

Servo-based mechanizm to make a foldable landing gearI'm always using this landing gear wheels in my projects because it's best price to strength, about 2,5-3$ and handle models up to 1 - 1,5 kghttps://s.click.aliexpress.com/e/_EvWNq3JAbout servos I...

Parts: * 3 x 9-gram servos * 2207 motor * 500/800mAh, 40C, 3/4S LiPo battery * 20/30Amp ESC * Receiver * Carbon/plastic tube, 10mm diameter with a 2mm border, approximately 30-40cm in length Print all the parts and attach the motor to the nose...

This device is a miniature precision locator and balancer, specifically designed to ensure accurate alignment of model aircraft components. It's essential to utilize the identical scale I've employed, allowing both parts to seamlessly interlock and...

This is a pylon racer completely made with Autodesk Fusion 360. The model is made while creating a tutorial that can be watched at https://www.youtube.com/channel/UCKh-KSuLAX90UopVnQd3Bcg in english and german language. Tis is work in progress, not...

Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=24229 Instructions Using the following settings: axle_clearance is set to 10 tolerance is set to 5 width has been selected as 30 diameter stands at 70 wall_thickness is...

Print SD card slot facing down. Surprisingly, this has little effect on flight handling even on a light foamie but I would advise fitting on right wing so that the drag is offset by the prop side-thrust. ... Fitted to the wing with Velcro, I couldn't...

Created by Customizer! Instructions Design Your Project Use the following settings: Axle Clearance: Increased to 10 mm for a smoother ride. Bike Width: Set at 17 inches for optimal balance. Tolerance:...

This is an integral component of a radio-controlled aircraft's tail section.

I'm looking for something to level out my radio-controlled aircraft. ...It requires two sturdy eight millimeter rods that I managed to salvage from a crashed model airplane, an AXN Floater Jet.

Introducing the initial model of a remote-controlled foam airplane, complete with a battery-powered motor and servos for enhanced maneuverability.

I built this spinner as a replacement for the one that broke on my Hobbyking P40 Funfighter. It has a diameter of 38mm, and I printed it in PLA - it's working flawlessly now. ...Check out the updated version of this design here:...

1.1m, 1800-2000gram designed for a 4250 motor around 800kv, spinning a ~12x6 prop. ...3300-4000mAh 4S with a suitable ESC, this should be a good acro/fast flier if you want it to be.

This tool is specifically designed for creating precise indentations in the center of hinge parts, as demonstrated by the model at http://www.thingiverse.com/thing:31249.

Based on my previous Battery Mount plate here: https://www.thingiverse.com/thing:4947126 While the old mount was meant to be used with Velcro straps or similar, this version is specifically designed to be used to mount Li-Ion Cell packs in a...

Modified from http://www.itsqv.com/QVM/index.php?title=File:MTM03.jpg, adjusted to meet requirements for assembly without glue using only M3 nuts and bolts. ...Made with high-quality PLA material, featuring an infill of 15% and a unique Gyroid fill...

special created for my fpv glider.did have a mount becose don't wonne put te cam in te nose of my glider.thats wy i created this mount for the caddx vista pro.

Motormount for Fun Bat 6mm Depron

It Soars: Flying High at 700 Grams Its nearly 700 grams of impressive weight, yet it's incredibly easy to repair. The interlocking system allows for seamless assembly and disassembly, making maintenance a breeze. Whether you're working with thick or...

For remotely controlled aircraft.

The latch on my 3dhs Edge 540 48" decided to disappear in flight. I designed this to quickly replace it. It is 8mm wide, 12mm tall and 25 mm long. the latch handle is 5mm deep and 12mm tall. the holes are slightly under-sized so will need...

Fun Mounts Galore for Speedy Bat Wing Model Using Strong 0.236-Inch Thick Light-Weight Board

I prefer not to double bend my pushrods because it's difficult and potentially can break the control horns. The Edge 540 designed by 3DLabprint is such a nice design with very tight movement of the control surfaces resulting in near zero backlash. In...

This is a custom housing for the Immersion VTX on my Volantex Ranger 1600 FPV aircraft. The base grips securely onto the fuselage, and I secured it using Loctite plastic bonder epoxy. The transmitter fits snugly inside; I leave it slightly loose for...

Speed pane concept with 3 meter wingspan

This human hasn't taken to the skies yet.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/dol74uLMnrP

This model remains grounded.

Designed a hatch for H9 Ultra Stick so I can pass 4 cables to the engine... can be edited to be completely closed, or maybe some cockpit with pilot onboard... ... glued some balza pices underneath in front to hold grip, and stock screw holds rear...

I designed this hook to store my E-flite Viper 70mm EDF jet. It is fairly large and should be compatible with a lot of different models. I load tested an ABS prototype printed at 10% infill to nearly 19lbs (8.6 kg) with minimal flex! Teh final...

Simple remix for smaller (1mm or 0.8mm, idk which one I have) push rods. ...Also added a shorter version