cr 10 mini enclosure 3d models
442991 3d models found related to cr 10 mini enclosure.thingiverse
Searching for an enclosure for my CR-10 Mini to print PET-G and ABS, I came across this: https://www.thingiverse.com/thing:2864118 A beautiful and simple solution, but it won't work for my CR-10 Mini because it was too short. I decided to make a few...
thingiverse
This enclosure for the CR-10 Mini has all the parts you need except screws and plastic walls as well ass two or three LACK table from IKEA. It has also a little door at the side to make it easier to change filament. ... Total height inside is 53 cm or...
thingiverse
An external enclosure for the MOSFET from in the CR-10 control box. The two halves are zip tied together. This is one part of a set of parts. The goal for this project is to place all of the internal components on the underside of an Ikea Lack table...
thingiverse
An external enclosure for the sMelzi motherboard from in the CR-10 control box. The two halves are zip tied together. This is one part of a set of parts. The goal for this project is to place all of the internal components on the underside of an Ikea...
thingiverse
Designed for the Creality CR-10 A parts list is in the included PDF. ... To seal up gaps I used Foam Window Seal can be found at a home improvement store ...
thingiverse
I did a fair amount of searching and wasn't satisfied with the cost or design of several of the enclosures available for the CR-10 and other larger printers, so I decided to design my own. This enclosure is fully-customizable and can be scaled up or...
thingiverse
... For 2nd door need to print all additional parts - door and hinges) Print with support and skirt. Pictures are from the first design - 2 mm walls. Second design come with 3mm walls https://pinshape.com/items/44114-3d-printed-cr-10-s-enclosure
thingiverse
It's a fully printed enclosure for the CR-10! I had tried ABS and nylon on the printer before with some pretty bad warping. The printer can do it, it just needs the heat to stay around the part and not float away and make the apartment warmer. My...
thingiverse
This is primarily a remix of Kiayoto's CR-10 enclosure. I removed the lower section of that enclosure and modded several pieces of the original. I had printed all of the original parts then made adjustments to suit my needs. I also modded the...
thingiverse
The Wood Piece Sizes are as follows: Front/Back - 18in x 25.5in (Door is however big you want it to be) Right Side (Front) - 12.5in x 25.5in Right Side (Back) - 11in x 25.5in Left Side (Front) - 12in x 25.5in Left Side (Back) - 10.5in x 25.5in...
youmagine
Ho realizzato per la mia cr-10 mini questo supporto per rendere più facile l'inserimento della micro sd tramite una proluga.
thingiverse
I found this on a google search for a CR-10 Enclosure. This is not my design! ... Original design credit goes to: Cscott on GitHub "https://github.com/cscott/3d-melltorp" Assemby Instructions: ...
thingiverse
This is just a holder to slip in a temperature gauge and attach it to the CR-10 enclosure from 3DUPfitters. (It should work on DIY enclosures as well.) Its designed specifically for this thermometer-- just slide it in. Its designed to attach...
thingiverse
Front and Back Corner Brackets: remix from 2020 Corner Bracket by TheStapler https://www.thingiverse.com/thing:2655498 Spool Holder is from Super Simple Spool Holder by bdx2000 https://www.thingiverse.com/thing:2165694 I used Y axis cable chain:...
thingiverse
CR-10 Enclosure. Remove all 3 Internal fans, Including the Power Supplies fan. Remove top cover for optimal cooling. Found best option for mounting the MOSFET was to use mounting tape. Mounted Power Supply using Mounting tape. This IS A...
thingiverse
A 3D Printer Enclosure that can fit a Creality CR-10 or any smaller 3D Printer / Device. ... - Frame is made from 1"x1" wood - Piano hinges are to be used for the doors - Plexiglass is used for the front panels to keep the printer visible while...
thingiverse
I am posting my plans to the enclosure for the CR-10. I made mine quite a bit wider so I can change filament and get to extruder easily, but I left minimum dimensions as well. I reused spool holder from CR-10 and mounted to frame. ... Here is most...
cults3d
I am posting my plans to the enclosure for the CR-10. I made mine quite a bit wider so I can change filament and get to extruder easily, but I left minimum dimensions as well. I reused spool holder from CR-10 and mounted to frame. ... Here is most...
thingiverse
I found Jackson238's thing for a CR-10 enclosure using larger Ikea tables, but did not like the use of magnets to hold the acrylic windows on the structure. As such, I took inspiration from the original designs and remade them in Fusion360 to...
thingiverse
CR 10 LIGHT Enclosure UNTESTED All are just recommended dimensions, same goes for the panels! One CR10 version accommodate the CR10 with the spool on top of the frame, second reduced on high with 100. This is just an example! Feel free to make...
thingiverse
This is a electronics enclosure styled like that of the Creality CR-10's. The enclosure is accessible from the top, the sides and screen are "hinged". This was one thing I did not like about the stock one from Creality when I wanted to make a change...
thingiverse
This is a group of components to make an enclosure out of 2 Ikea Lack tables, and 0.18 inch thick foam board from Dollartree. The front doors open and slide back into the cabinet for easier access to the printer. It's still a work in progress. ...I...
myminifactory
guide filament pour CR-10 Mini PLA 0.2 / 15% imprimé sans supports
thingiverse
Easy turn knob fits over existing knob on CR-10 Mini to make it easier and faster to change settings, especially setting nozzle temperature. Use outer edge of knob for fine settings. Use knob crank handle for coarse settings. Add supports to just...
thingiverse
CR 10 ENCLOSURE - SUPER-LIGHT series UNTESTED Use 4mm plexiglas sheet. Filament and Cable WINDOWS comes also in a split in two versions, allowing to mount the sealing material - sponge, texture... etc! ... DESIGN TO PRINT WITHOUT SUPPORT - by...
thingiverse
CR 10 S ENCLOSURE METAL FRAME CABINET See also: https://www.thingiverse.com/thing:3233857 or https://www.thingiverse.com/thing:3230158 SQUARE PIPE 40X40X1.5mm STANDARD CR 10 S - No alteration to original - out of the box design! UPDATE 31 OCT 2018...
thingiverse
These are the parts for an enclosure I made for my CR-10. It uses cheap activated carbon respirator filters by Hawk. This dramatically reduces the smell of the fumes of ABS printing for me. This filter set up is in no way a complete filter system.
thingiverse
https://youtu.be/Ok9uSThp73A Update : 2019-07-15 1) Air filter / scrubber : https://www.thingiverse.com/thing:3749365 Update : 2018-03-12 1) 2 and 3 are 38mm short, uploaded correct files to match assembly guide Update : 2018-01-02 1) handle_washer...