rc skis 3d models
31639 3d models found related to rc skis.thingiverse
RC airplane skis, 18cm by 6cm. The "light" version is 1.5 mm thick and 30grams (printed in PLA at 100% infill) and quite flexible, it is suitable for a lighter plane. The heavy duty version is 4mm thick and 71g (printed in PLA at 100% infill), very...
thingiverse
Ski de dimension divers pour plusieurs types de RC aéronefs d'ailes entre 1000 - 1600 mm. Le bout (spatule) doit être courbé avec un fusil à air chaud à votre convenance. Different size of skis for RC planes from 40 - 60 " wingspand. ...The tip...
thingiverse
Skis made for a Turbo Timber / Timber. ...Sand/Paint to give a smooth bottom surface to reduce friction on the snow. Use a rubber band on each ski to keep the tips up when off the snow.
cults3d
Skis for rc aircraft. I have included two sizes. The smaller size is good for small planes like Flite Test mighty minis. The larger size should be good for larger Flite Test planes but you can scale them to any size you need. ...You will need to mirror...
thingiverse
These skis are designed to fit a Tamiya Madbull or other RC car with similar steering arms (5mm dia. x 20mm long). Also uploaded STLs for mk2 skis with a more angled pattern to bite when turning. ... ...
thingiverse
This is a custom designed ski set for a 1/10 scale RC truck. The design is a little different than the off the shelf versions as this replaces the steering hub instead of bolting onto the axle. This reduces the risk of the ski rolling over and takes...
thingiverse
I designed this set of skis for my traxxas rustler to traverse the snow more efficiently. On the back wheels I have a pair of sand/snow paddle tires to get more traction. ...Also be where that not all rc cars are water/snow proof.
thingiverse
These are skis which can be printed and used with any RC aircraft for takeoffs and landings on snow. I use them on my Horizon Twin Otter and they're great fun. They are 7.5 inches in length and 1.5 inches wide. They are designed for 3mm wire gear...
thingiverse
Made some skis to my Thunder tiger cessna 177 to be able to fly on snow/ice during winter.
thingiverse
This a ski set for 1/10 RC cars, which utilizes rubber bands to keep the skies level, and not bounce all over the place. It also raises the front end for better clearance in snow (vs tires). ...These fit most 1/10 scale buggies and truggies and you can...
cults3d
This a ski set for 1/10 RC cars, which utilizes rubber bands to keep the skies level, and not bounce all over the place. It also raises the front end for better clearance in snow (vs tires). ...These fit most 1/10 scale buggies and truggies and you can...
myminifactory
This a ski set for 1/10 RC cars, which utilizes rubber bands to keep the skies level, and not bounce all over the place. It also raises the front end for better clearance in snow (vs tires). ...These fit most 1/10 scale buggies and truggies and you can...
myminifactory
No support needed for this print, However for maximum strength I would recommend to print it on its side. ...And then you do need support.
thingiverse
... and 4mm axle shafts. I use them in addition to the rear wheels that I have designed. Update: Many have requested the right ski file, I have mirrored it and updated the thing. ... Link to the rear wheels: https://www.thingiverse.com/thing:2727391
thingiverse
RC Plane Ski's to fit 25 size planes tried and tested on my Tucano don't suppose the snow is going to last long here in the uk but at least that's one thing of my bucket list to take of and land on snow if you have any snow left give it a go
thingiverse
This is an RC car ski that sits about 2" tall. You will need a screw to hold the 2 parts together, I haven't tested it yet because I have no snow. ...And this is one of the first things that I have designed so don't expect it to be perfect.
thingiverse
The big difference is the way of mounting and means of keeping the ski's pointing up, but not too much. The ski is attached to the landing gear by a single wheel collar. The set screw in the collar has been replaced by a 20mm long M3 bolt. Attached...
thingiverse
Skis for your rc plane I fix it in my flyzone switch for test Very good product
thingiverse
Check this improved version: https://www.thingiverse.com/thing:4756025 I designed this Ski for my medium sized RC airplanes. Check also the matching rear Ski : https://www.thingiverse.com/thing:4755028 There are 2 attachment point for a spring or...
thingiverse
This model is for making a ski plane for flying in winter. The ski has a hole under the axis of 3mm. ... http://ali.pub/33xfos - spring http://ali.pub/33xfqj - spring retainer on the axis https://youtu.be/e7ExtrBfmL4 - Aircraft landing gear...
thingiverse
Bend the spring 90deg so that when installed the bent end will go into the front hole on the ski Put the spring back on tight to the ski then put the collar on, you will need to mark the spring again and bend, first a 90deg bend and then a 3/4 loop...
thingiverse
This is a ski set that should be universal for a 4mm shaft and 12mm hex drive on an RC car or truck. The parts should get glued or epoxied together. On my printer I had to scale to 104% to get accurate dimensions. I also added a snow wheel that i...
sketchfab
Ski wax bottles that i made for school project. ...These are modeles with 3ds max.
thingiverse
Designed a multi-piece Snow Ski design that uses 2 parts that are repeated in design. No need to print a left side and a right side separately. Break the ski? Reprint the bottom portion instead of a single one piece unit. The base ski has...
thingiverse
New Update: I TESTED it on snow, it ROCKS! Also you may want rear snow wheels http://www.thingiverse.com/thing:1952583 Old: This is a fixed version, and it is still on testing. I DELETED the first version, because it could not work. Only fits for...
cults3d
Created to fit around a wheel, slots added for velcro. ...SLDPRT file provided for adjustments to fit your airplane.
thingiverse
this is another skidoo spindle from tinkercad! I was looking at pascals video and paused it and made something that looks like his spindle. ...Imma keep making parts for the time being and I hope yall enjoy them.