rc stand 3d models

The model is a compact stand designed specifically for remote-controlled airplanes that feature a fuselage approximately 1.57 inches in diameter.

Simple yet sturdy stance for rc models. Print settings: All components except belka.stl require the following: layer height, 0.2 mm; top/bottom layers, 3; outline/perimeter shells, 3; infill, 20%. Belka.stl demands special treatment with layer height...

This car stand is designed specifically for 1/8 and 1/10 scale vehicles, measuring 160mm x 100mm in size with a compact height of just 25mm when closed and expanding to approximately 75mm when fully open. To assemble the stand, you'll need to print...

The Human Model RR Car stand is designed to be 80mm tall and boasts a sturdy 50mm x 50mm top plate for maximum stability. ...To assemble, simply print the model upside down for optimal results.

Axle stands at a modest size, allowing for easy adjustments to suit individual preferences. ...Feel free to inquire about modifications or simply tailor its dimensions to meet your specific needs.

This is a basic remote control car stand that works perfectly for on-road remote control vehicles. ...However, it might not be suitable for off-road remote control cars due to its relatively low profile.

This will keep the car from slipping off the stand and also add height needed for keeping the wheels off the ground. See the link below for the foam. ... ...

A simple yet effective stand for lifting tires off the shelf, preventing them from developing flat spots. This design can be used as a standalone unit or combined with a 3/16" dowel rod for added stability. ...To print this design, lay it on its side,...

Wanted a foldable car stand, which could also serve as a shock-stand for different cars, shocks, ... I drive an Xray XB8, XT8 and XT2 ... but this car-stand will suit ANY 1/8th or 1/10th buggy. I might need to make it a bit higher to suit Truggies...

Wanted a foldable car stand, which could also serve as a shock-stand for different cars, shocks, ... I drive an Xray XB8, XT8 and XT2 ... but this car-stand will suit ANY 1/8th or 1/10th buggy. I might need to make it a bit higher to suit...

<p>Easy to print without supports. ...Tested with PLA and PETG.It is a very handy gadget to organize your tools on the table.Update:I have added a bigger version of the Tools Stand.

I became tired of chasing the motors around the bench every time wanted to solder some motor wires onto them, so a few minutes later and here we have a stand capable of holding a 540 or 550 sized motor while you solder your cables to it!

***Very basic and simple stand to lift the tires off the shelf to keep them from getting a flat spot. Use as stand alone or join with 3/16" dowel.Lay on it's side to print. ...Do two at once and you have a set.</p><h3>Print...

Wanted a foldable car stand, which could also serve as a shock-stand for different cars, shocks, ... I drive an Xray XB8, XT8 and XT2 ... but this car-stand will suit ANY 1/8th or 1/10th buggy. I might need to make it a bit higher to suit Truggies...

To prevent the stand from sliding around, I plan on adding a rubber mat to the bottom - I've already found a great source on Amazon. I was initially going to add some of that mat to the upper parts as well, but then I decided to try printing those...

** Notice: This is a Very Large Print when Finished & Assembled **\r\n** 279 Meters or 85% of 1 Spool **\r\n** Approximately $21.25 @ $25.00 per 1KG Spool **\r\n\r\nThis 3D printed replica stands tall, just like its wooden counterpart available at...

4mm Laser Cut CQ stand for RC Airplanes

RC tools stand

Here is my design for a sturdy, non-adjustable 1/10 RC axle stand that you can print without support, although using some will likely yield better results. ...The white stand in the picture was one I attempted to print in nylon but couldn't achieve the...

This is a very simple 1/10 RC Car stand to prop your car up so that the wheels aren't touching the ground/desk. It also has interchangeable plates with hole sizes 12-20mm to hold shocks. All 3 shock plates fit in the center area for storage. ... You...

## 1/10 Scale RC Stand This stand is a great way to keep your tires looking their best by taking the pressure off, so they stay nice and round. It consists of two pieces that fit together with a tab in the center. To print them separately, you can...

RC Car Stand with a Rotating Top That Spins Freely. Two Adjustable Heights to Suit Your Needs. Works Perfectly with 1/8, 1/10, 1/12 Scale RC Cars from Popular Brands like Traxxas Rustler and Nitro Sport, Stampede. It Rotates 360 Degrees for Easy...

My version of the RC jack stand is a one-piece print that doesn't require support or brim. It perfectly fits 2.2 wheel size crawlers, but can be scaled in any slicer to meet individual needs. The pictures showcase the original-sized big red stands...

This is during the trial and error of CAD for me and the RC Car Stand take 1 is printing as we speak but its too small but since I have a 1/28 Team Associated TC28 I can use take 1 for that Truggy. This on the other hand is sufficient for much bigger...

This is during the trial and error of CAD for me and the RC Car Stand take 1 is printing as we speak but its too small but since I have a 1/28 Team Associated TC28 I can use take 1 for that Truggy. This on the other hand is sufficient for much bigger...

This is a high-performance *RC Car Stand* that works seamlessly with my Traxxas E-Revo 1/16, designed to fit the MERV perfectly but also accommodating larger models. **Key Features:** * A fully rotating stand (360 degrees) allows for effortless...

This is a Custom RC Car Stand that I built to work on my Traxxas E-Revo 1/16 (it's sized so that it fits the MERV perfectly, but should be able to hold larger models as well).\n\nFeatures:\n* Spins freely in all directions (360 degrees)\n* Adjusts...

It's a car stand for 1:24 RC. ... Addtional parts: M3 screw bolts x 1 M3 nuts x 1

RC car display stand It is designed to display the 1/10 scale RC cars on selves in style. It needs 8mm adhesive buffer pads (x10) for anti-slip. ...

A simple Stand for the XPRESS XQ2S RC Car.The holes fit the body of the car, so it stays safe.Added a two parted Stand which can be glued together easily. ...Faster print time and more stable.Wholes of the Version 1 didnt fit well