rc toe gauge 3d models
46380 3d models found related to rc toe gauge.thingiverse
For details see RC Toe Gauge Mk.2 Manual.pdf . TLDR; Set the gauge on the back side of the wheels, then move it to the front side and read the scale. ## FAQ ### Can it be used for other types of cars? Yes, although I'd recommend a regular...
thingiverse
My RC aircraft handle on the ground better it they have a little wheel toe-in. For those planes that have the bent aluminum landing gear use a pair of these wedges on each wheel to add about 4° of toe-in. One wedge is placed on the outside (wheel...
thingiverse
RC Heli Pitch Gauge Based on cheap pitch gauges. Scale is 1 degree, longer lines every 5 degrees. ... To assembly you need: 2xM3 screws (minimum 8mm length) 2xM3 nuts 1xRubber band
cults3d
RC Car Setup Camber Toe Steering Key Features: -Designed for RC vehicles -For camber, toe, steering and caster measurement -Help with chassis tuning -Wheel mounting support for M3, M4 and M5 -Will fit printer bed 240mm x 240mm -Optional part included...
thingiverse
I design these ride height gauges as I do a lot off rc racing. And ride height gauges always goes missing at track side. As people ask to use it and never give it back. ...But with these you will know that they are yours
cults3d
This camber gauge will give you a direct measurement of the wheel camber compared to the more common set and compare camber gauges. The camber gauge arm has an integrated printed spring that provides the preload. It was designed for use with 1:10...
thingiverse
This is a camber gauge for RC cars. Place the flat wheel on your car in place of a tire. This gives you a flat surface to line up the gauge with. It fits a standard 12mm nut. If you know you need this, I bet you know what to do with it. The gauge is...
cults3d
This is a camber gauge for RC cars. Place the flat wheel on your car in place of a tire. This gives you a flat surface to line up the gauge with. It fits a standard 12mm nut. If you know you need this, I bet you know what to do with it. The gauge is...
thingiverse
Mount for Helicopter Pitch Gauge, good to measure camber on 1/10 touring cars. You can use a M4 screw or a magnet (glued on) to attach the gauge. ... Added v6, which is usable for left AND right.
cults3d
Made this rc ride height to check the height of my 1/10th scale Drifter. ...Height from 4-13mm
thingiverse
Made this rc ride height to check the height of my 1/10th scale Drifter. ...Height from 4-13mm
thingiverse
Control throw gauge for setting control surfaces. Additional items needed are 1/16 music wire 3/4 inch long , plastic clothes pin, 3mm button head screw and lock nut 25mm long. ... https://youtu.be/DtrIPxueMTA
cults3d
I have been adjusting my camber and toe by eye looking to aligne the big bulky iregular tires on my RCs for a couple of years. Then I decided to get more precise on this. Made me those plates that fits my 1/8 scale truggy and 1/16 scale Summit. ... I...
thingiverse
Made a holder for my ebay/china level box to set pitch on my RC helicopter. You might have to sand the sliders if your printer is "sloppy" as I made it thight fit to not wobble when measuring. Could prolly be better but I mocked it up quickly just...
thingiverse
A simple ride height gauge for RC buggy that I printed several pieces to keep in different place, The corresponding ride height is shown on the bottom edge, There is one face without any numbers and it is intended to face to the bed when printing.
thingiverse
This is a copy of Schelle Racings wire caddy made for 12 or 13 gauge wire. ...
thingiverse
Height Gauge for offroad buggies 1/10th and 1/8th scale A new design (previous https://www.thingiverse.com/thing:3704124) The idea came from a height gauge from Hudy ... but I wanted a handle to be easier to manipulate (and cheaper :) ) Now a new...
prusaprinters
A little ride hide gauge I designed for a friend. ...The pucks fit into the handle and then you can slide it under the chassis to ensure it is at the correct height. </p><p>Especially useful for those chassis where the centre of it is slightly...
thingiverse
It has to be HARD to insert the axle into the gauge needle and to the pin. The frame hole should allow the needle to rotate freely. Insert the M6 nut in the needle. Do it with the axle aswell with a drop of glue on it before insertion. Insert the...
thingiverse
... First thing I wanted to try was rear toe-in. Tamiya supplies 53793 (AFAIK originally meant for the DF-02, used in the ms) which are a bit hard to come by. Also I wanted to make my own...as usual :-D Update: v6 now with higher material strength.
thingiverse
I was browsing around for RC stuff and saw not much DIY stuff for touring cars. ...Found some ride height gauge but no droop gauge so I decided to make one. Made a droop gauge then I decided why not just include the ride height gauge. ...Enjoy!
thingiverse
Parametric RC ride height gauge block with embedded height text at the top.
thingiverse
First draft of my upcoming set of tools for RC cars. ... Updated version coming in a few days. Will include 1 - 15 mm gauge + camber gauge
thingiverse
I was browsing around for RC stuff and saw not much DIY stuff for touring cars. ...Found some ride height gauge but no droop gauge so I decided to make one.
cults3d
A Model for RC Accesories 1:10 Scale Car or Drift, it has some detail on its gauge so you cant paint the indicator
thingiverse
Adjustable ride height gauge for RC cars. I designed it for my 1/10th Offroad. ... Can be adjusted from 16mm to 19mm by moving the insert.