reciprocating saw adapter 3d models

Printed both of these with Priline TPU to use as a vacuum adapter for a Shopvac: 1.) "VacAttach_Hitachi to ShopVac v3.stl" for a Hitachi 12 inch chop saw 2.) "VacAttach_Delta 10 inch Chop Saw to ShopVac v5.stl" for a Delta 10 inch chop saw Uploaded...

This adapts my 1.25" shop vac hose to my 2.375" Hitachi chop saw dust port.Printed in TPU, 2 shells, 100% infill, no support, 60C bed, 230C hotend, 30mm/sPrint...

Adapter ring allows one inch chop saw blade to be installed on 20mm arbor saw. Choose tallest ring that still lets blade clamp close fully. 5mm worked best, but size may vary depending on specific needs. Ring is usually thicker than the blade due...

I wanted to connect my Wet/Dry Vacuum Cleaner from Makita (which seems to be made by Nilfisk) with a Festool Adapter Set(Dust extraction set CS 70 AB - 488292) to the Hikoki C10RJWAZ Table Saw. So I made an Adapter for a Hikoki C10RJWAZ Table Saw to...

... of tools. ...but I believe shop vac hoses are pretty standard at 1.75". The dustport on the table saw is a little strange at 2.55" I printed it with solid infill but I'm sure it'd be fine otherwise. ...It's a bit thicker than most adapters at .095"

...Unfortunatley, I could not find a good adapter to attach the saw dust output from the table saw to the vacuum hose. There are a few out there but none I could find that fit perfect. I also did not want to purchase a bunch until I found one that fit.

This is an adapter to up-size the Rigid 1.25" orange/black flexible vacuum hose to a Wen track saw dust port. ... I used 0.15 Horizontal Hole Retraction on my Ender 3 Pro to make the print "on-the-nutz" accurate.

Designed this adapter to connect Husky 2.5 gallon dry/wet vacuum to Dewalt 7485 (745) table saw main exhaust. Printed with PLA, 20% infill, no supports, 0.4mm nozzle, 0.3mm line height. ... Uploaded STL, STEP and Fusion 360 files (if you would need...

# Dewalt 7485 Table Saw to Shop Vac 2.5hp Vacuum Hose Adapter ## Overview I have a Dewalt DWE 7485 Table Saw. I also have a small ShopVac 2.5hp vacuum. Unfortunatley, I could not find a good adapter to attach the saw dust output from the table saw to...

This is a vacuum adapter to attach a larger Ridgid shop vacuum to the Ryobi TSS103 sliding miter saw. Should fit snugly at 100%. Ridgid says their hose is 2.5" diameter but it's slightly smaller. You can trust me on this one. I would never lie to...

... that barely stayed in. ...This fits on the outside of my Dewalt Miter Saw 1.5" attachment as well as the outside of my shopvac (2 1/4"). I increased the dimensions a touch to make it fit snug with PETG on my printer. ...You may wish to scale as needed.

Printing at 0.16 or 0.20 mm might not give satisfactory results, although I didn't try/test.Update (v2): I found the original adapter was fitting a bit too tight on my miter saw, so I've slightly increased the inner diameter (by 0.25mm). ... This was...

A vacuum hose securely clips onto the adapter, yet allows for smooth rotation as you maneuver the saw. ...It is worth noting that Dyson advises against using their vacuum to collect fine dust particles like sawdust, as this can potentially damage the...

Adapter for Makita Plunge Saw to fit a Camvac 2.5" hose Customized version of http://www.thingiverse.com/thing:1571860 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1571860 Instructions Using the following options:...

This is a custom adapter designed for seamless connection between a Dewalt 7480 portable table saw and a Rigid shop vacuum with a 1.875 inch hose. By adding a taper to the inside diameter, I achieved a precise fit that eliminates any potential leaks...

...Unfortunatley, I could not find a good adapter to attach the saw dust output from the table saw to the vacuum hose. There are a few out there but none I could find that fit perfect. I also did not want to purchase a bunch until I found one that fit.

This is a right angle vacuum hose adapter to connect a Vacmaster hose to a Dewalt DWS715 miter saw. This is designed to be a female to female adapter, with a 42mm inner diameter on the long side, and a 45mm inner diameter on the short side. The...

Here is a very simple adapter to connect a Chicago Electric 10" Sliding Compound Miter Saw from Harbor Freight Tools (HFT SKU numbers 61971, 96697, 98199, 90891, 61307, 61972, 56708, or 57343) directly to a standard 1.25" tapered shop vac hose...

The two objects allow you to connect either a 50mm (DN50) or a threaded 40mm sawdust vacuum hose to the Bosch GCM8 SJL miter saw. The 50mm model goes over the adapter, and can also be used with off-the-shelf DN50 pipe tubing. The 40mm variant can be...

The 50mm model goes over the adapter and can also be used with off-the-shelf DN50 pipe tubing whilst the 40mm variant can be used to screw the hose into the adapter.By looking at the two objects it should be clear which is which.If you want or need...

The 50mm model goes over the adapter and can also be used with off-the-shelf DN50 pipe tubing whilst the 40mm variant can be used to screw the hose into the adapter. By looking at the two objects it should be clear which is which. If you want or...

marble saw ,Wood Saw,

&nbsp;I designed this adapter for my Kreg track saw for hooking it up to the Rigid 1-7/8 shop vac. I found a much better solution after that from Rockler but maybe this print will be useful to someone else.</p><ul><li>It fits the original twist lock...

Needed to connect my Rigid R4514T Table Saw to my Shop-Vac 5 Gallon Wet Dry Wall Mount Vac. ...This one is friction fit and tight!

Links the dust port of the skil table saw 90 degree elbow to the 1.75" DeWalt shop-vac hose. Very sturdy connection and makes your dust collection a little simpler. ...Enjoy !

Use this design to step down the lower 2.5-inch vacuum port on a DeWalt table saw to the 1.75-inch vacuum hose of a DeWalt shop vac.

This remodeled design incorporates a flexible pipe attachment suitable for a BOSCH 4310 miter saw, with customizable parameters via parametric SCAD software. Easily reconfigure it for other tools or varying miter saws. Be cautious when printing the...

... using Tinkercad. ... I created two versions: one with the dust port in the middle and one offset. I prefer the offset version because it provides more clearance. This setup enables me to use a regular flexible hose that attaches directly to the saw.

I need an adapter that will connect my WD3 vacuum tube to the Makita MLT100 dust collector's output port.

This is a simple ring adapter. Outside Diameter is 57mm (fits the 2.25inch hole) Inside diameter is 45.4mm (fits the 1.75inch Ridgid hose end) It's about 31mm in length I printed this with 30% infill and came out fairly rigid. Had to...