record display holder 3d models

Samsung display

... ...To find the specific components for this set, search for "Micro-Chess Pieces" or look up Thing ID 752232. If you're interested in seeing how this display model is set up, check out "Micro Chess Table: Display Model" or search for Thing ID 752250.

... made it a bit wider, since my displays won't fit the original design. ...I measured my display to be approximately 29.3mm wide, while the original model was 28mm wide. ...I made the model 29.9mm wide internally so It'll probably still be a tight fit.

###GPU display stand purely for display purposes, to display your old gpu on a nice stand. Made some changes to the original, no supports needed, made the bracket easier to print and a lot stronger, also made it printable on printers with a...

Used two M4 Screws to fix the original Snapmaker touch panel holder (the one with the angle).

Xbox 360 holder compatible with Kinect for Xbox 360 and designed specifically to fit a 23-inch Pro Lite monitor.

The camera is broken, wanted to display it on a shelf. Designed in Fusion 360, printed on an Ender 3 with Chip 0.2mm settings. ... After printing (~7hrs) I sanded and used spray filler, sanded again then spray painted it.

A versatile pedestal stands prominently, showcasing rings on full display. ...Equipped with a compact plate, it allows users to affix labels detailing prices, descriptions, and other essential information at their convenience.

Für den Umbau meines SOVOL SV01 musste ich das Display auf die Linke Seite anbringen. Hierfür habe ich diese Halterung entworfen. ...Ihr könnte auf Youtube anschauen wie das ganze aussieht: https://youtu.be/RYbedIfLLbQ

Ender 3 Left Control Display Holes at the back are 3mm in the 3d model this is just a mirrored control panel of the ender 3 with some slots for sd cards

GPU display stand purely for display purposes, to display your old gpu on a nice stand. Made some changes to the original, no supports needed, made the bracket easier to print and a lot stronger, also made it printable on printers with a smaller...

This remix seamlessly integrates a tool holder with a cover, resulting in a robust and functional design. Print it out flat, securing it with manual support on the ribbon cable opening - the rest will print effortlessly without any additional...

ST Dupont lighter stand or display purposes. Can be nice to have the collection presented on the same displays. The lighter displayed is a Ligne1 Full size, so should fit most models. (There is one without branding for when you got other brands, I...

... and a skirt (no brim or raft). Infill density does not significantly impact this part.After printing, mount to the side of an Apple 27" LED Cinema Display using 1/2" VHB (very high bond) double-sided tape, such as: https://amzn.to/3uust6P 

This is a 3D model to mount the RC070N 7in IPS display, inside your PC CASE!I took the Elecrow RC070N 7 inch, 600p, IPS, touch display for making this mod.The model was made with Solidworks 2020.It is a really snug fit, so no screws are required for...

Human Record Player Displays Vibrant Hues

I redesigned the original tarantula to make the display more accessible, attaching it directly to the structure to simplify movement of the printer. To improve visibility, I also added a lighting system, incorporating an LED strip that can be powered...

I utilized the Waveshare 7.5 ePaper display in a recent project and was concerned about the display adapter board, so I designed a simple case for it to protect against accidental damage if my picture frame were to be knocked over. To avoid printing...

Mount a bracket with a small angle, designed for easy attachment to a countertop holder dish. Please refer to the counter holder dish section for further details. ... The print surface is optimized for printing when laid flat on its largest, most stable...

This guide explains how to mount your Makerbot Replicator 2/2X LCD display on the front of the unit at a 30-degree tilt, making it much easier to see the display at this angle. Three STL files are provided for printing in black ABS: 1- The LCD TILT...

To add an 8-digit display to a Halloween costume, you'll need to secure it firmly in place. One side should be left open for easy access to the wiring, making any necessary adjustments or repairs a breeze. ...This can be achieved by applying a strong...

enclosure for shunt and display all in one, just drill a hole or 2 on the short sides to pass your wires through, wire everything up, and have the shunt floating inside, if more airflow is needed for hot shunts use the vented back panel(WIP)

Low filament, single slot version of the GPU display stand made by IVIarc_Antoine.I needed it to organize all my GPUs, I thought I'd share.It's a bit scuffed, but it does what it needs to.Print time is around 20 minutes, only 3-4g of filament each

... to a collection! ...:) Display your pens in style with this miniaturized rocket scaffolding model! Designed for a 7.5mm tapered chrome Cross pen I have, but as shown in photos it does also work with other pens as well! ... Print without supports.

The 20x2 Character VFD (Vacuum Fluorescent Display) - SPI interface - 20T200DA2JA, available at http://www.adafruit.com/products/347, has been thoroughly tested and confirmed to be functional. ...To print this product with optimal settings, utilize a...

used to create 5 sided display case enclosure printed with clear filament can be used with 3mm glass or plastic sheeting glass_clip_1 - supports the top sheet glass_clip_1 - connects all corners glass_clip_1 - fills gaps at the base created by...

... to build a Motorola GM1200, which is widely favored by enthusiasts working on Amateur Radio projects. ...A clip is included to securely attach your device, along with a protective cover to shield the display connector from dust when it's not in use.

This is a versatile bullet holder that fits perfectly on a 6.5 Swedish Mauser rifle, but its compact design also makes it suitable for other firearms with similar barrel sizes.

A compact and practical display stand designed to hold ten 10ml eliquid bottles securely in place. The stand is crafted to showcase the bottles neatly, ideal for retail environments or personal use. To accommodate standard TPD compliant bottles...

... front. You need some USB cable. There's a source code so you can modify values for you cable. Original display bolts are used so no need for extra ones. Print instructionsPrinting it laying on the back side is the preferred orientation (easiest).