redcat 51 3d models
12151 3d models found related to redcat 51.
thingiverse
Raspberry Pi Zero Mount for Redcat Everest 10 for FPV Flight. ... Mount a Raspberry Pi Zero to your Redcat Everest 10 for an Enhanced FPV Experience. ...Perfect for DIY Project Lovers and Hobbyists.
thingiverse
Redcat Racing Everest Gen7 Front Steering Arm Mounts Require Printing at a 45-Degree Angle for Optimal Results.
thingiverse
Designed for use with Redcats rear shorty battery conversion, using 2200mah 105x33x24mm batteries instead. ...Will bolt straight to their conversion plate
thingiverse
Hello there, I've created a mod for the RedCat Gen8 Axle that's perfect for building a sturdy 6x6 rig. ...Good luck with your project!
thingiverse
Redcat Gen8 Spur Gear Spare Part File SpurGear_Module08_32DP_45T.stl This is the gear spare part for Redcat Gen8 RC car, Module 0.8, 32DP, 45Teeth, which works with the Redcat Pinion Gear 17T (Part No. 11177). You can also order a plastic one from...
thingiverse
This is a replacement part for the Redcat Tornado Exp Pro spoiler, requiring no additional support and taking approximately 35 minutes to print both pieces. Printing two units is essential, as this design is not compatible with the stock part on its...
grabcad
The Redcat Racing differential I utilized to construct my personal RC is surprisingly compact compared to my expectations upon purchase. A more advantageous model could have been acquired prior to this experience. Nonetheless, I hope others find this...
thingiverse
... faces but only one set of barrels to use them in. ...Redcat has no plans to make barrels available so I made these totally unofficial barrels for all the RCers who want to use them on other cars. ...Take it, mod it, do what you like , all yours kids.
thingiverse
**These axle housings use a Redcat Everest-10/GEN-7 internals** - **4-link** and **3-link with panhard** versions - **(4x) M3x35 bolts + original bolts from Redcat axles** - **10 deg. of caster** built-in for better steering and drag link clearance -...
thingiverse
Redcat Caldera 10E hex wheel/axle hub. Printed this at .3 and .2 without much visible difference, both at 100% infill. ...Works well but could use a little bit of flare towards the base where it interfaces with the bearing.
thingiverse
Rear shock towers for the Redcat Gen8 truck. This helps you with the Jeep Wrangler body from Injora. You need to drill a hole on the metal frame. ... Use high wall thickness instead of high infill.
thingiverse
Redcat Racing BS904-005 Front Bumper Chassis for Earthquake 3.5, Earthquake 8E, Earthquake 3.0, Shredder, Aftershock 3.0, Aftershock 3.5, Aftershock 38E. ... Printed with Cura 4.6.1, lay the part flat to print
thingiverse
I whipped up a custom paddle tire for my Redcat Volcano EPX Pro - printed in TPU, it fits snugly onto any 2.8 style rim with standard glue-on beads. ...Enjoy!
thingiverse
Redcat gen8 portal axle steering servo mountYou will need to reomove the sway bar and convert to a 4 link (very easy)Link length needed is 60mm not including link ball ends
thingiverse
Designed a servo mount for the Redcat Racing Sixty Four Impala R/C lowrider. I picked up a Power HD R-12 servo and had to create a mount to fit it properly. It uses the existing screws from the original servo and fits the chassis quite well. ...
thingiverse
Here is the rear shock bar for the Redcat Gen8 v2. I designed this because we needed to move the battery to the rear. So, when also doing this remove the old larger one and install this one so you have enough clearance for the battery. ...This should...
thingiverse
Made for mockup creation in 3D software, this allows anyone to play and develop upgrades for the Redcat Gen7. Several prints and comparisons were conducted to create these. New Upgrade! ...STEP/IGES/SAT/SMT and Fusion 360 files are now available on...