redcat gen8 bumpers 3d models
11311 3d models found related to redcat gen8 bumpers.thingiverse
Front bumper for Redcat Gen8. ...First draft, with three lights.
cults3d
Trx-4 to Redcat Everest Gen8 V2 Bumper Mount works with front or back
thingiverse
Center mounted servo bracket for Redcat Gen8 Scout. I was too cheap to go with an aluminum one, so I worked this one up myself. Included are standard bumper height and raised bumper height models, pick your flavor! During installation, screws may...
thingiverse
side magnet holder for redcat gen8 and xt60 x3 hub. ... D16 mm magnets use in hubs.
thingiverse
Dashboard for RedCat Gen8. The instruments might be printed in clear PLA for lighting. ... https://youtu.be/4nbhn5c87KE
thingiverse
A simple floor pan for the back of a Redcat Gen8 rc truck. I just wanted something to block light from shining through the truck to make it look more solid and scale appropriate. It is sized to have the rear bumper moved forward a couple of holes to...
thingiverse
This GoPro mount for the Redcat Gen8 is a direct replacement for the rear bumper. Early testing shows solid strength and stability, even surviving an inadvertant rollover test. I printed the file vertically, which did generate some fairly...
thingiverse
This is a 1/10 scale hitch mount for a Redcat Gen8 vehicle. ... This is designed to work with a 4.3mm ball stud.
thingiverse
This is a replacement piece for the link end connectors for the Redcat Gen8. ...Or any RC that uses 5mm ball ends and 3mm screws.
thingiverse
Slider for Redcat Gen8. A bit beefier than the OEM design so they should hold up pretty well. I'd skip PLA and go with PA6, PC, or maybe TPE. PLA or PETG should last for a while just not idea. Mirror for the opposite side or just print 2 and...
thingiverse
THIS is a roll cage I made for my chopped Redcat Gen8. Just make sure when you place the front piece to fix it to the highest position possible, or the 2 rear parts won't fit properly. The differents parts are glued together with epoxy glue. I...
thingiverse
Headlight adapter to give your Gen8 some additional pizazz. ...Accepts 23mm Googly eyes.
thingiverse
I made this to go over the IH logo on the side of a Gen8 Scout II. ...Enjoy
thingiverse
This is a hitch I created to fit the Redact Racing Gen8 and Gen8 V2. I could not find any hitches to buy online and the ones I 3d printed did not come out so nice. I have not printed this part yet so if there is anything wrong, feel free to tell me.
thingiverse
Used the dimensions from the Gen 8 Roof Rack that Redcat made and remade it entirely. this one is slightly beefier and has better mounting and print-ability. Shouldn't need supports and should be able to withstand most light rollovers. The original...
thingiverse
Hello! ...This is my modified part for RedCat Gen8. New flat central plate, new battery tray and wheel hex hub 7mm, 8/4mm and 10.5mm. Goodluck! ... Add 5.01.2020, Hello, I added forced central plate, good luck!
thingiverse
It is made from the RedCat Gen8 kit. I post links to the video of the project. I hope someone wants to repeat my project and show it in action. Good luck to everyone! ... https://youtu.be/baFHaTEF3QE https://youtu.be/tzqfga4hwIo ...
thingiverse
Magnet mount hole is included on top, two holes on each fender, Diameter 10mm, deep 2.6mm Why made this: I bought the Redcat Gen8 PACK (PreAssembled Chassis Kit) , unfortunately it has NO wheel fenders set on included! I think the chassis looks a...
pinshape
Print Parameters Layer Height: 0.3mm Perimeter Walls: 3 Number of Top and Bottom Layers: 3 Infill: 35% Rectilinear Battery Relocation Options Redcat Gen8 Rear Shorty Battery Conversion Redcat Gen 8 Sideways Battery Conversion Redcat Gen8 Low CG...
thingiverse
A bracket for mounting a lighting control board to a Redcat Gen 8 RC rock crawler. The cover for the board is thing 3842975. https://www.thingiverse.com/thing:3842975 This contains the board it fits. ... ...
thingiverse
Here it is, the Bumper mount for the Everest Gen 7, customized to accept the Redcat racing Gen8 bumper #####Redcat parts on Thingiverse are released under the Creative Commons License Attribution- NonCommercial- ShareAlike 4.0 International (CC...
thingiverse
Hello. ...My mod for redcat gen8 axle for building 6x6. ...Good luck!
thingiverse
Rear shock towers for the Redcat Gen8 truck. This helps you with the Jeep Wrangler body from Injora. You need to drill a hole on the metal frame. ... Use high wall thickness instead of high infill.
thingiverse
And the 2nd file, it works with tamiya pinions gears, installed and tested on the redcat gen8 pack....so just in case, if you don't have the redcat gen8 pinion gear (11177) like me and can only use a tamiya small pinion gear, you can use this file2....
thingiverse
For various reasons, not the least of which is the creation of R/C scale Halo Warthogs, one may wish to add steering control to the rear of a Redcat Racing Gen8. Here I'll attempt to illustrate two different methods of achieving this feat. Neither...
thingiverse
Here is the rear shock bar for the Redcat Gen8 v2. I designed this because we needed to move the battery to the rear. So, when also doing this remove the old larger one and install this one so you have enough clearance for the battery. ...This should...
pinshape
This will mount inplace of the stock bumper mounts and is designed to be used with aftermarket bumpers that mount on the outside of the frame like Scaler Fab Bumpers (https://www.scalerfab.com/collections/all-products/redcat-gen8-scout-ii). ...
thingiverse
I made these for the screw-on type of magnetic body mounts for the redcat gen8. It replaces the normal lock nuts for a cleaner look in the wheel wells. I did mine using the club5 racing magnet kit. It's also useful as a drill guide for locating the...
thingiverse
Redcat Scout Gen8 vice clamp press mold to bend the steering link. The stock link did not have enough bend to clear the diff case cover which drastically limits steering angles. Once bent it should give 2-3mm of clearance of the diff case cover...