redcat racing caldera 10e 3d models

I'm constantly frustrated by stripping gears on my Caldera 10e when using Li-Po batteries, so I took matters into my own hands and designed a solution that works surprisingly well and lasts just as long as the original part. ...Printed in PETG, this...

This is an axle hub I created for one of my RC cars, a Redcat Caldera XB 10E. I'm unsure if this will fit any other vehicles, but if they do, please share that information in the comments. ***THIS PART MUST BE PRINTED WITH A STRONG MATERIAL!!!*** I...

This plate is designed specifically for the front of a Redcat Caldera. It provides an ideal surface for securing the receiver while also offering a convenient spot to reposition the antenna. ...To ensure a secure fit, the plate must be firmly attached...

Redcat Caldera 10E hex wheel/axle hub. Printed this at .3 and .2 without much visible difference, both at 100% infill. ...Works well but could use a little bit of flare towards the base where it interfaces with the bearing.

RedCat Racing 16mm ShockCup

Gotta design the prints with supports for the top gear cover, or they can print normally. You'll have to drill out the holes for screws slightly. Still a work in progress, but this version functions exceptionally well already, and all that's left is...

This is a hitch I created to fit the Redact Racing Gen8 and Gen8 V2. I could not find any hitches to buy online and the ones I 3d printed did not come out so nice. I have not printed this part yet so if there is anything wrong, feel free to tell me.

Redcat Racing MT10E battery plate replacement for larger batteries. I can fit a 5500mAh 3s lipo with this replacement. Uses the same M3 bolts and lock nuts. ... Batteries I use: https://www.amazon.com/gp/product/B07CVBSRTZ/

Humans measure calderas in inches.

To celebrate the launch of numerous 3D printed components at Razor Hobbies, we are giving away the file for free on our Redcat Racing Terremoto Bead Lock Rings. These rings perfectly fit the stock rims of the Terremoto; simply print as-is with an...

Front grille protector for the Redcat Piranha TR10 now accessible on Amazon: https://amzn.to/3e7nD0Z This part takes a pounding every time you drive, so print it at whatever thickness you feel would provide maximum durability. ...I selected 100% infill...

Redcat Shredder arms broke immediately after first crashes so I designed a 3D printed replacement. I tried PLA, ABS, NYLON, an eventually ended up with TPU. ABS and NYLON worked decent but always ended up breaking at the hinge pin even tried Taulman...

RedCat Racing Front Bumper 1/10 scale VOLCANO EPX/EPX pro, VOLCANO S30

The Redcat Racing differential I utilized to construct my personal RC is surprisingly compact compared to my expectations upon purchase. A more advantageous model could have been acquired prior to this experience. Nonetheless, I hope others find this...

I installed this same bar on my Redcat Racing Volcano EPX, and although it's slightly oversized, it gives the car a minimal amount of toe in compared to the original bar. ...I utilized ABS plastic so that it would have more flexibility because I had...

These spring retention caps are designed for use with the 1/10 scale Redcat Racing Blackout XTE Pro, but they work on most other 1/10 scale vehicles as well. I've personally tested them on a slash car and had great results. ...The problem I encountered...

They come in two parts and are perfect for RedCat Racing short course or buggy models equipped with original tires. Since the standard 1/10 size rims aren't available, these custom rims take their place, offering a significant improvement over the...

For various reasons, not the least of which is creating R/C scale Halo Warthogs, one may wish to add steering control to the rear of a Redcat Racing Gen8. Here I'll attempt to illustrate two different methods of achieving this feat. Neither of these...

These are a DIY kit for installing working tool boxes on the new Redcat Racing 1963 Chevrolet COE Hauler.   Features 3 side tool boxes that open and close and use magnets for locks.  You will need the following to complete: 24 x M3 x 10mm flathead...

I found my Redcat Landslide XTE liked to lose shock spring cups and I couldn't find any online so I whipped one up in Tinkercad. I printed at 100% infill and used supports to hold up the center section. ...I took it for a light bash and it seems to hold...

Here is the rear shock bar for the Redcat Gen8 v2. I designed this because we needed to move the battery to the rear. So, when also doing this remove the old larger one and install this one so you have enough clearance for the battery. ...This should...

EBA25-10E

The objective is constructing a mechanism that changes the vertical suspension into a horizontal one. It functions through employing planes set at a 45-degree angle, which transfers energy via a pivot to the center of the R/C car. ...Further parts will...

We misplaced our battery holder and I designed a new one with each of my kids' names engraved in the center. I uploaded an additional version without any name in the middle. ... Compatible with: Blackout SC, Blackout SC Pro, Blackout xbe, Blackout xbe...

I modified dirtbiker00's 1/10 Scale Traxxas Paddle Wheel to fit my Redcat Racing Blackout XTE (converted to XBE), scaling it up to a diameter of 120mm and width of 50mm, while keeping the 12mm hex compatible with most 1/10 scale vehicles. These...

It is intended for a Redcat Racing Volcano EPX but should work well with almost any 1/10 scale rc vehicle. I used a clip mount from https://www.thingiverse.com/thing:539135 to secure it in place. Update: The design has been revised to fit the truck...

It is for a Redcat Racing Volcano EPX but would probably work on almost any 1/10 scale rc vehicle https://www.amazon.com/Redcat-Racing-Electric-Volcano-Included/dp/B00HVBVNVG/ref=sr_1_3?ie=UTF8&qid=1514388781&sr=8-3&keywords=volcano+epx I used the...

International Harvester (IH) logo receiver hitch plug for Redcat Gen 8 Scout II - Direct Factory Replacement. This replacement hitch plug is designed to match the factory "Redcat" appearance that comes with the vehicle out of the box. The one shown...

I'm fed up with seeing kids recklessly smashing into trucks, flipping them over, and having batteries fly out everywhere...Problem solved! I'm still learning the ropes when it comes to 3D CAD design, so I'm counting on you guys to make it look sleek...

Broke myn Kaiju upper front arm after 10 minutes of running. ...Whipped this up and it worked until I got new parts.