redcat racing caldera 10e 3d models

A simple snap-on bracket lets you quickly install or remove the Sense ESS One 2017 sound module from a Redcat Gen7 Crawler with ease.

This was a quick model I made for my Redcat Gen 7 when I upgraded to the Flysky GT5 and needed to mount the receiver. ...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Print horizontal lines with reinforced backing to ensure stability. ...Seal the finished project with vibrant, high-gloss 2K epoxy adhesive designed specifically for use with 3mm LED components.

I designed this specifically to overlay the IH logo on the side of an original 1966-1971 Gen8 Scout II. ...Check it out!

I decided to create new bumper supports for my blackout without purchasing them. I figured it would be easier that way. ... Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: .2500mm Infill: 100%

To upgrade your setup, you'll need to install a 30mm fan directly into the suspension tower at the front, and then carefully slice through the bodywork. ...This allows the provided hood scoops to seamlessly slide on top of the fan, protruding from the...

My sons steering knuckle broke on his RC truck so I made this it seems to work fine some sanding may be required

Because I can't own something without messing with it... often even before using it... I swapped out the radio gear on my fs-gt3b and now I need to switch to a 3s 5000. So, I jumped into CAD tonight (it arrived tonight) and measured everything out,...

Roll bar for rc crawler with separated ligts

Printable Diff case, may need slight sanding due to printer tolerances.

Shouldnt have any problems printing. ...might need some slight sanding.

Ok, here we go. That's my 1st contribution. First of all, i want place the servo in the axle, so i use the https://www.thingiverse.com/thing:3582941 Then i found i need to remove the Panhard Link. So i start to modify this one. The...

So I spent 2 hours measuring the redact volcano and designing this body and tweaking but I never printed it and I'm kind of sad about that . ...but I'm 90% it will work I just don't want to use a whole roll of filament to make it

three part roof protector

Printing Recommendations: (Total print time = +/- 23 hrs, +/- 265 grams of filament, Largest Dimension 190mm) Infill: 5% - Hexagon Filament: PLA / PETG Layer: .2mm Print orientation requires attention to detail. Center Console: Rotate -65 degrees,...

This creation was crafted within Tinkercad's intuitive interface. ...To edit and refine this design, visit the online workspace at https://www.tinkercad.com/things/hES5R6d6D3E.

This is a remix of the print from ohioorbs.I found the walls on that version were too high to allow for the stock frame brace.The mounting holes also didn't line up on my truck.So I created this remix with shorter walls and revised mounting holes.It...

RedcatGen7 Skid plate Features: +Very smooth belly, allow sliding on obstacles. +Fits perfet to the Stock Gear. +Rigid design. +Access to the Driveshaft set screwes without disassemble the skid plate. ... Hardwere Required: Type ...

Shipping has been horrible lately and I need to get back on the trail. I whipped this up on tinkercad to get me rolling again. I am not a professional by any means. It works and that all I cared about. ...Happy Trails.

I had an amazing time trying out this snorkel system! I managed to clean and use an inline foam block that came in a box, which worked perfectly with the weedeater type filter. However, I found it easier to attach just the stock air filter unit to...

Replacement center skid that is flat and lets you move your lower links in toward the center helping to eliminate most of the torque twist. Unlike others on the market this one utilizes the factory link rod ends. ... Will need: - 4x M3 x 10 screws ...

smaller light weight battery tray.fits max 2200 size packsmounts in stock location. ...stock hardware will work

Headlight upgrade kit that adds a burst of personality to your Gen8 vehicle. ...Compatible with 23mm googly eyes for an extra dash of charm.

I designed this custom bumper using Tinkercad after my Redcat's front bumper gave out, with no local Redcat parts available to me. Please feel free to modify and comment on the design if needed. ...I 3D printed this bumper in Ninjaflex Armadillo...

Redcat Gen7 Crawler Servo Mount. ... It has two servo mounting positions: - 1st holes are for the stock location with stock servo horn - 2nd set of holes is Higher for a longer aftermarket servo horn

As the built-in field rotator indicator of the RedCat 51 cannot easily be adjusted to the 0 position of the scale, I found it more convenient to have a freely adjustable indicator as part of the distance ring. RedCat 51 has a backfocus distance of...

Bruder snow plow conversion, to RedCat Scout II Gen8 Snowplow extended by 60mm, with 2x30mm wings 270mm wear blade The parts are glued together or some drilling can be required, and then some 2mm screws are needed

... hard to find timely replacement parts. I broke mine on my second battery the first day I got the truck so I was really foaming at the mouth to keep driving and designed this to hold me over until I could upgrade to the aluminum part Redcat offers.